Dodge avenger 2013 Owner'S Manual Download Page 169 | Manualshive

Page: 169 / 631

background image

Call Termination

To end a call in progress, momentarily press the

but-

ton or the end soft-key. Only the active call(s) will be
terminated and if there is a call on hold, it will become
the new active call. If the active call is terminated by the
far end, a call on hold may not become active automati-
cally. This is cell phone-dependent.

Redial

•

Press the “Redial” soft-key,

•

or press the

and after the “Listening” prompt and

the following beep, say “Redial”,

•

After the “Listening” prompt and the following beep,
say “Redial”,

•

The Uconnect® Phone will call the last number that
was dialed from your mobile phone.

Call Continuation

Call continuation is the progression of a phone call on the
Uconnect® Phone after the vehicle ignition key has been
switched to OFF.

NOTE:

The call will remain within the vehicle audio

system until the phone becomes out of range for the
Bluetooth® connection. It is recommended to press the
“transfer” soft-key when leaving the vehicle.

Uconnect® Phone Features

Emergency Assistance

If you are in an emergency and the mobile phone is
reachable:

•

Pick up the phone and manually dial the emergency
number for your area.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

167

«
...
167
168
169
170
171
...
»

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for avenger 2013

Brand: Abarth Pages: 176

Brand: Garmin Pages: 2

Brand: Vauxhall Pages: 177

Brand: APEXi Pages: 18

Brand: Prorack Pages: 15

Brand: PEUGEOT Pages: 128

Brand: Schumacher Electric Pages: 87

2009 ESCALADE ESV

Brand: Cadillac Pages: 602

Brand: Phonocar Pages: 2

Brand: Maserati Pages: 210

Brand: OnStar Pages: 22

Brand: GMC Pages: 120

Brand: Prime Tech Pages: 6

Brand: A-Tach Pages: 2

Brand: CrimeStopper Pages: 1

Brand: Power Acoustik Pages: 4

Brand: TEINHOF Pages: 2

Brand: Subaru Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands