Dodge avenger 2013 Owner'S Manual Download Page 249

Page: 249 / 631

NOTE:

Any chassis/suspension modifications to the ve-

hicle will effect the performance of the Adaptive Cruise
Control.

Activating Adaptive Cruise Control (ACC)

You can only activate ACC if the vehicle speed is above
20 mph (32 km/h).

When the system is turned on and in the READY state,
the Electronic Vehicle Information Center (EVIC) dis-
plays “Adaptive Cruise Ready.”

When the system is OFF, the EVIC displays “Adaptive
Cruise Control Off.”

Adaptive Cruise Control Buttons

1 — DISTANCE SETTING
2 — RES

3 — SET

4 — CANCEL
5 — ON/OFF
6 — MODE

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

247

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for avenger 2013

Reviews:

Related manuals for avenger 2013

Brands by name

Popular brands

Dodge avenger 2013, Owner'S Manual

Search results

Summary of Contents for avenger 2013

Reviews:

Related manuals for avenger 2013

Brands by name

Popular brands