manualshive.com logo in svg

Dodge avenger 2013, Owner'S Manual

The Dodge Avenger 2013 Owner's Manual is a comprehensive guide that provides essential information about your vehicle. With easy-to-understand instructions and detailed illustrations, this manual is available for free download from manualshive.com. Ensure optimal performance and safe driving by having this manual at your fingertips.

Share
Download
background image

Road Tire Installation

1. Mount the road tire on the axle.

2. Install the remaining lug nuts with the cone shaped

end of the nut toward the wheel. Lightly tighten the
lug nuts.

WARNING!

To avoid the risk of forcing the vehicle off the jack,
do not tighten the lug nuts fully until the vehicle has
been lowered. Failure to follow this warning may
result in personal injury.

3. Lower the vehicle to the ground by turning the jack

handle counterclockwise.

4. Finish tightening the lug nuts. Push down on the

wrench while at the end of the handle for increased
leverage. Tighten the lug nuts in a star pattern until each

nut has been tightened twice. The correct tightness of
each lug nut is 110 ft-lbs (150 N·m). If in doubt about the
correct tightness, have them checked with a torque
wrench by your authorized dealer or service station.

5. After 25 miles (40 km) check the lug nut torque with a

torque wrench to ensure that all lug nuts are properly
seated against the wheel.

JUMP-STARTING PROCEDURES

If your vehicle has a discharged battery it can be jump-
started using a set of jumper cables and a battery in
another vehicle or by using a portable battery booster
pack. Jump-starting can be dangerous if done improperly
so please follow the procedures in this section carefully.

NOTE:

When using a portable battery booster pack

follow the manufacturer’s operating instructions and
precautions.

518

WHAT TO DO IN EMERGENCIES

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for avenger 2013

Acdeos AXS FL Installation Instruction preview
AXS FL
Brand: Acdeos Pages: 7
Jeep 2011 grand cherokee Accessories Quick Reference Manual preview
2011 grand cherokee
Brand: Jeep Pages: 22
Jeep 2013 Grand Cherokee Owner'S Manual preview
2013 Grand Cherokee
Brand: Jeep Pages: 704
Jeep 2012 Liberty Owner'S Manual preview
2012 Liberty
Brand: Jeep Pages: 558
Mazda 2 2016 Owner'S Manual preview
2 2016
Brand: Mazda Pages: 720
GReddy Intercooler Kit Type 31 Installation Manual preview
Intercooler Kit Type 31
Brand: GReddy Pages: 9
hc-cargo 171850 Mounting And Operation Instructions preview
171850
Brand: hc-cargo Pages: 60
TATA Motors Tata Indigo Diesel Owner'S Manual & Service Book preview
Tata Indigo Diesel
Brand: TATA Motors Pages: 190
Safe Fleet Prime Design HBR-E-FT33B Assembly Instructions Manual preview
Prime Design HBR-E-FT33B
Brand: Safe Fleet Pages: 12
Baja Designs 447575 Instructions preview
447575
Brand: Baja Designs Pages: 5
JANE StrataPlatform Instructions Manual preview
StrataPlatform
Brand: JANE Pages: 58
Mercedes-Benz E55AMG Service Manual preview
E55AMG
Brand: Mercedes-Benz Pages: 39
Yakima K614 Manual preview
K614
Brand: Yakima Pages: 12
FALCON RIDGE CF-1000-WD05 Instructions For Installation And Care preview
CF-1000-WD05
Brand: FALCON RIDGE Pages: 6
Ranger design 1525-FTR Installation Manual preview
1525-FTR
Brand: Ranger design Pages: 24
Safe Fleet PRIME DESIGN HRR-369-E-UM3-96 Manual preview
PRIME DESIGN HRR-369-E-UM3-96
Brand: Safe Fleet Pages: 12
Kocchi's 772161M1 Manual preview
772161M1
Brand: Kocchi's Pages: 4
ECS FIA-030-B Fitting Instructions preview
FIA-030-B
Brand: ECS Pages: 4

Brands by name

Popular brands

Load more brands