manualshive.com logo in svg

Dodge avenger 2013, Owner'S Manual

The Dodge Avenger 2013 Owner's Manual is a comprehensive guide that provides essential information about your vehicle. With easy-to-understand instructions and detailed illustrations, this manual is available for free download from manualshive.com. Ensure optimal performance and safe driving by having this manual at your fingertips.

Share
Download
background image

Starting

The characteristics of E-85 fuel make it unsuitable for use
when ambient temperatures fall below 0°F (-18°C). In the
range of 0°F (-18°C) to 32°F (0°C), you may experience an
increase in the time it takes for your engine to start, and
a deterioration in driveability (sags and/or hesitations)
until the engine is fully warmed up.

NOTE:

Use of the engine block heater (if equipped) is

beneficial for E-85 startability when the ambient tempera-
ture is less than 32°F (0°C).

Cruising Range

Because E-85 fuel contains less energy per gallon/liter
than gasoline, you will experience an increase in fuel
consumption. You can expect your miles per gallon
(mpg)/miles per liter and your driving range to decrease
by about 30%, compared to gasoline operation.

Replacement Parts

Many components in your Flexible Fuel Vehicle (FFV) are
designed to be compatible with ethanol. Always be sure
that your vehicle is serviced with correct ethanol com-
patible parts.

CAUTION!

Replacing fuel system components with non-ethanol
compatible components can damage your vehicle.

Maintenance

CAUTION!

Do not use ethanol mixture greater than 85% in your
vehicle. It will cause difficulty in cold starting and
may affect driveability.

5

STARTING AND OPERATING

485

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for avenger 2013

Horn Tools HISDMSPTRA01 Mounting Instructions preview
HISDMSPTRA01
Brand: Horn Tools Pages: 6
Mobis G4211ADE00AL Installation Instructions Manual preview
G4211ADE00AL
Brand: Mobis Pages: 16
Subaru starlink Manual preview
starlink
Brand: Subaru Pages: 216
FormFit HD 10L07 Installation Instructions preview
HD 10L07
Brand: FormFit Pages: 2
GMC YUKON 2018 Owner'S Manual preview
YUKON 2018
Brand: GMC Pages: 425
Mazdaspeed QSEA 51 96Z Installation And User Instructions Manual preview
QSEA 51 96Z
Brand: Mazdaspeed Pages: 8
IBASE Technology MPT-3000V User Manual preview
MPT-3000V
Brand: IBASE Technology Pages: 100
Modifry Products S2000 Windscreen Camera Mount Quick Start Manual preview
S2000 Windscreen Camera Mount
Brand: Modifry Products Pages: 2
Dometic Heki 2 Installation And Operating Manual preview
Heki 2
Brand: Dometic Pages: 158
Monacor Carpower CAP-20 Quick Manual preview
Carpower CAP-20
Brand: Monacor Pages: 2
Metra Electronics 99-8714 Installation Instructions Manual preview
99-8714
Brand: Metra Electronics Pages: 8
Dodge Dodge Challenger SRT8®Challenger SRT8 392 2012 Specifications preview
Dodge Challenger SRT8®Challenger SRT8 392 2012
Brand: Dodge Pages: 5
Edelbrock 65932 Installation Instructions preview
65932
Brand: Edelbrock Pages: 2
CTEK D250S Dual Manual preview
D250S Dual
Brand: CTEK Pages: 84
Beper P205DIF100 Manual preview
P205DIF100
Brand: Beper Pages: 52
Enduro EM203 User Manual preview
EM203
Brand: Enduro Pages: 52
Dometic LMC Eriba Nova Service Manual preview
LMC Eriba Nova
Brand: Dometic Pages: 24
Ford F-250 Super Duty 2022 Owner'S Manual preview
F-250 Super Duty 2022
Brand: Ford Pages: 740

Brands by name

Popular brands

Load more brands