Dodge avenger 2013 Owner'S Manual Download Page 606 | Manualshive

Page: 606 / 631

background image

Treadwear

The Treadwear grade is a comparative rating, based on the
wear rate of the tire when tested under controlled conditions
on a specified government test course. For example, a tire
graded 150 would wear one and one-half times as well on
the government course as a tire graded 100. The relative
performance of tires depends upon the actual conditions of
their use, however, and may depart significantly from the
norm due to variations in driving habits, service practices,
and differences in road characteristics and climate.

Traction Grades

The Traction grades, from highest to lowest, are AA, A, B,
and C. These grades represent the tire’s ability to stop on
wet pavement, as measured under controlled conditions
on specified government test surfaces of asphalt and
concrete. A tire marked C may have poor traction perfor-
mance.

WARNING!

The traction grade assigned to this tire is based on
straight-ahead braking traction tests, and does not
include acceleration, cornering, hydroplaning, or
peak traction characteristics.

604

IF YOU NEED CONSUMER ASSISTANCE

«
...
604
605
606
607
608
...
»

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for avenger 2013

Brand: Kargo Master Pages: 5

Brand: Masterack Pages: 4

Brand: Over Armour Offroad Pages: 5

Brand: XTC Pages: 4

Brand: TATA Motors Pages: 92

Brand: Ford Pages: 458

Brand: Ratio Pages: 12

Brand: Horn Tools Pages: 8

Brand: J. Strong Pages: 2

Brand: Westfalia Pages: 10

Brand: Mobridge Pages: 20

Brand: Ford Pages: 2

Brand: Mazda Pages: 7

Brand: CAME Pages: 14

Brand: Chipolino Pages: 11

Brand: SAF-HOLLAND Pages: 12

Brand: Edelbrock Pages: 1

Brand: Toyota Pages: 422

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands