manualshive.com logo in svg

Dodge avenger 2013, Owner'S Manual

The Dodge Avenger 2013 Owner's Manual is a comprehensive guide that provides essential information about your vehicle. With easy-to-understand instructions and detailed illustrations, this manual is available for free download from manualshive.com. Ensure optimal performance and safe driving by having this manual at your fingertips.

Share
Download
background image

CAUTION!

Do not use a portable battery booster pack or any
other booster source with a system voltage greater
than 12 Volts or damage to the battery, starter motor,
alternator or electrical system may occur.

WARNING!

Do not attempt jump-starting if the battery is frozen.
It could rupture or explode and cause personal injury.

Preparations For Jump-Start

The battery is stored under an access cover in the trunk.
Remote battery posts are located on the right side of the
engine compartment for jump-starting.

NOTE:

The remote battery posts are viewed by standing

on the right side of the vehicle looking over the fender.

Remote Battery Posts

1 — Remote Positive

(+)

Post

2 — Remote Negative

(-)

Post

6

WHAT TO DO IN EMERGENCIES

519

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for avenger 2013

iDataLink Maestro Installation Manual preview
Maestro
Brand: iDataLink Pages: 9
iArmor IA-N179 Manual preview
IA-N179
Brand: iArmor Pages: 6
tams elektronik 54-01016 Manual preview
54-01016
Brand: tams elektronik Pages: 44
P-Invent Troller User Manual preview
Troller
Brand: P-Invent Pages: 4
LXE Akerstroms Tx700 Configuration Manual preview
Akerstroms Tx700
Brand: LXE Pages: 146
POOL-LINE 110050 Assembly Instructions preview
110050
Brand: POOL-LINE Pages: 2
TATA Motors INDICA eV2 XETA CNG Supplemental Owner'S Manual preview
INDICA eV2 XETA CNG
Brand: TATA Motors Pages: 24
PAC AP4-GM61 Quick Start Manual preview
AP4-GM61
Brand: PAC Pages: 5
Percon Falcon 655 User Manual preview
Falcon 655
Brand: Percon Pages: 49
TATA Motors NEXON Owner'S Manual preview
NEXON
Brand: TATA Motors Pages: 232
Hyundai 2001 Elantra Owner'S Manual preview
2001 Elantra
Brand: Hyundai Pages: 168
Roadmaster Even Brake 9400 Owner'S Manual preview
Even Brake 9400
Brand: Roadmaster Pages: 20
Volkswagen Zubehör 000 071 105 D Installation Instructions Manual preview
000 071 105 D
Brand: Volkswagen Zubehör Pages: 133
Charge Amps Halo Pole Mount Manual preview
Halo Pole Mount
Brand: Charge Amps Pages: 14
LedGlow Advanced Million Color Installation Instructions preview
Advanced Million Color
Brand: LedGlow Pages: 4
Vauxhall MasterFit Manual preview
MasterFit
Brand: Vauxhall Pages: 4
Van Guard VG162S Fitting Instructions preview
VG162S
Brand: Van Guard Pages: 3
AA Products RB0002 Instruction Manual preview
RB0002
Brand: AA Products Pages: 6

Brands by name

Popular brands

Load more brands