Dodge avenger 2013 Owner'S Manual Download Page 27

Page: 27 / 631

Transmitter Battery Replacement

The recommended replacement battery is one CR2032
battery.

NOTE:

•

Perchlorate Material — special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate

•

Do not touch the battery terminals that are on the back
housing or the printed circuit board.

1. Remove the emergency key by sliding the mechanical

latch on the back of the RKE transmitter sideways
with your thumb and then pull the key out with your
other hand.

2. Insert the tip of the emergency key or a #2 flat blade

screwdriver into the slot and gently pry the two halves
of the RKE transmitter apart. Make sure not to damage
the seal during removal.

Emergency Key Removal

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for avenger 2013

Reviews:

Related manuals for avenger 2013

Brands by name

Popular brands

Dodge avenger 2013, Owner'S Manual

Search results

Summary of Contents for avenger 2013

Reviews:

Related manuals for avenger 2013

Brands by name

Popular brands