manualshive.com logo in svg

Dodge avenger 2013, Owner'S Manual

The Dodge Avenger 2013 Owner's Manual is a comprehensive guide that provides essential information about your vehicle. With easy-to-understand instructions and detailed illustrations, this manual is available for free download from manualshive.com. Ensure optimal performance and safe driving by having this manual at your fingertips.

Share
Download
background image

NOTE:

Press the

⬙

ESC Off

⬙

switch, to place the Electronic

Stability Control (ESC) system in

⬙

Partial Off

⬙

mode,

before rocking the vehicle. Refer to “Electronic Brake
Control” in “Starting And Operating” for further infor-
mation.Once the vehicle has been freed, press the

⬙

ESC

Off

⬙

switch again to restore

⬙

ESC On

⬙

mode.

CAUTION!

•

When “rocking” a stuck vehicle by shifting be-
tween DRIVE and REVERSE, do not spin the
wheels faster than 15 mph (24 km/h), or drivetrain
damage may result.

•

Revving the engine or spinning the wheels too fast
may lead to transmission overheating and failure.
It can also damage the tires. Do not spin the wheels
above 30 mph (48 km/h) while in gear (no trans-
mission shifting occurring).

WARNING!

Fast spinning tires can be dangerous. Forces gener-
ated by excessive wheel speeds may cause damage, or
even failure, of the axle and tires. A tire could
explode and injure someone. Do not spin your vehi-
cle’s wheels faster than 30 mph (48 km/h) or for
longer than 30 seconds continuously without stop-
ping when you are stuck and do not let anyone near
a spinning wheel, no matter what the speed.

6

WHAT TO DO IN EMERGENCIES

523

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for avenger 2013

Safe Fleet PRIME DESIGN VRI3-E-PM11 Manual preview
PRIME DESIGN VRI3-E-PM11
Brand: Safe Fleet Pages: 12
Volvo 2004 V70 (Swedish) Användarmanual preview
2004 V70
Brand: Volvo Pages: 188
Yakima K674 Instructions Manual preview
K674
Brand: Yakima Pages: 13
Menabo 000081000000, Fitting Instructions Manual preview
000081000000,
Brand: Menabo Pages: 11
AutoWatch 457 Rli Wiring Diagram preview
457 Rli
Brand: AutoWatch Pages: 4
Parkeon StradaPAL Installation Manual preview
StradaPAL
Brand: Parkeon Pages: 43
Weltmann KFZ-Teile 9B500016 Fitting Instructions Manual preview
9B500016
Brand: Weltmann KFZ-Teile Pages: 12
Cadillac 2011 SRX CROSSOVER Owner'S Manual preview
2011 SRX CROSSOVER
Brand: Cadillac Pages: 416
TIE DOWN LONGRUN 86103 Assembly/Installation Instructions preview
LONGRUN 86103
Brand: TIE DOWN Pages: 2
Toro Security Cage Kit Installation Instructions Manual preview
Security Cage Kit
Brand: Toro Pages: 8
Cadillac 2004 Seville Customer Convenience/Personalization Manual preview
2004 Seville
Brand: Cadillac Pages: 20
Pyle PLRD146 User Manual preview
PLRD146
Brand: Pyle Pages: 8
Rugged Ridge 53701.52 Installation Manual preview
53701.52
Brand: Rugged Ridge Pages: 5
Ford Focus 2008 Quick Reference Manual preview
Focus 2008
Brand: Ford Pages: 2
Toyota 4Runner 1999 Owner'S Manual preview
4Runner 1999
Brand: Toyota Pages: 285
RAM Cargo Van 2014 Owner'S Manual preview
Cargo Van 2014
Brand: RAM Pages: 666
Waeco PerfectView LCD350 Installation And Operating Manual preview
PerfectView LCD350
Brand: Waeco Pages: 36
Maserati MC 20 2022 Roadside Assistance Manual preview
MC 20 2022
Brand: Maserati Pages: 37

Brands by name

Popular brands

Load more brands