Dodge avenger 2013 Owner'S Manual Download Page 179

Page: 179 / 631

•

If multiple numbers are available for the contact select
which number you would like to have the message sent,

•

Press “Send” or “Cancel”.

Send Messages Using Voice Commands:

•

Press the

button,

•

After the “Listening” prompt and the following beep,
say “Send message to John Smith mobile”,

•

After the system prompts you for what message you
want to send, say the message you wish to send or say
“List”. There are 18 preset messages.

While the list of defined messages are being read, you can
interrupt the system by pressing the

button and

saying the message you want to send.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

177

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for avenger 2013

Reviews:

Related manuals for avenger 2013

Brands by name

Popular brands

Dodge avenger 2013, Owner'S Manual

Search results

Summary of Contents for avenger 2013

Reviews:

Related manuals for avenger 2013

Brands by name

Popular brands