Dodge avenger 2013 Owner'S Manual Download Page 356 | Manualshive

Page: 356 / 631

background image

Phone / Bluetooth

•

Paired Devices

This feature shows which phones are paired to the
Phone/Bluetooth system. For further information, refer
to the Uconnect® Supplement.

SIRIUS Setup

•

Channel Skip

SIRIUS can be programmed to designate a group of
channels that are the most desirable to listen to or to
exclude undesirable channels while scanning. To make
your selection, touch the Channel Skip soft-key, select the
channels you would like to skip. Then touch the arrow
back soft-key.

•

Subscription Info

New vehicle purchasers or lessees will receive a free
limited time subscription to SIRIUS Satellite Radio with
your radio. Following the expiration of the free services,
it will be necessary to access the information on the
Subscription Information screen in order to re-subscribe.

Touch the Subscription Info soft-key to access the Sub-
scription Information screen.

Write down the SIRIUS ID numbers for your receiver. To
reactivate your service, either call the number listed on
the screen or visit the provider online.

NOTE:

SIRIUS Travel Link is a separate subscription.

354

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
354
355
356
357
358
...
»

Summary of Contents for avenger 2013
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for avenger 2013

Brand: Uniden Pages: 16

Brand: Uniden Pages: 20

Brand: Spiral Audio Pages: 2

Akerstroms Tx700

Brand: LXE Pages: 146

GMC Yukon Denali 2005

Brand: Cadillac Pages: 456

Brand: Saab Pages: 63

Brand: R&G Pages: 20

Brand: Whispbar Pages: 70

Brand: GARO Pages: 15

Brand: Carcomm Pages: 2

Brand: Mercedes-Benz Pages: 398

Brand: Lexus Pages: 830

Brand: CITROEN Pages: 86

Brand: PERODUA Pages: 43

Brand: Istar Pages: 6

Sportsman 40-0125

Brand: Westin Pages: 2

Brand: Rajant Pages: 11

Brand: PAC Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands