Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 604 | Manualshive

Page: 604 / 922

background image

TEST

ACTION

APPLICABILITY

6

Turn the ignition off.
Disconnect the hoses from the TIP Solenoid.
Install a plug on the TIP Solenoid hose B connection point.
Connect a vacuum pump to the TIP Solenoid hose A connection point.
With vacuum pump apply 20 inches of vacuum to the TIP Solenoid hose A connection
point.
NOTE: Vacuum reading should not drop below 10 inches within 5 seconds.
Does vacuum read above 10 inches for at least 5 seconds?

All

Yes

→

Go To

7

No

→

Replace the TIP Solenoid.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

7

Turn the ignition off.
Disconnect the hoses from the TIP Solenoid.
Install a plug on the TIP Solenoid hose C connection point.
Connect a vacuum pump to the TIP Solenoid hose A connection point.
Attempt to apply 20 inches of vacuum to the TIP Solenoid hose A connection point.
NOTE: Vacuum should escape through the Solenoid hose B connection
point.
Does vacuum escape through the Solenoid hose B connection point?

All

Yes

→

Go To

8

No

→

Replace the TIP Solenoid.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

8

Turn the ignition off.
Disconnect the hoses from the TIP Solenoid.
Install a plug on TIP Solenoid hose C connection point.
Connect a vacuum pump to the TIP Solenoid hose B connection point.
NOTE: For the result of this test to be accurate the solenoid must be turned
on. Apply 12 volts and Ground to the appropriate solenoid terminals to turn
the solenoid on.
With vacuum pump apply 20 inches of vacuum to the TIP Solenoid hose B connection
point.
NOTE: Vacuum reading should not drop below 10 inches within 5 seconds.
Does vacuum read above 10 inches for at least 5 seconds?

All

Yes

→

Go To

9

No

→

Replace the TIP Solenoid.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

268

DRIVEABILITY - NGC

P1854-TIP BARO OUT OF RANGE —

Continued

«
...
602
603
604
605
606
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Green Motion Building

Brand: Eaton Pages: 12

Brand: Toyota Pages: 56

Brand: Barker Pages: 2

10-8002-C11670C

Brand: Saleen Pages: 17

Brand: Yakima Pages: 11

Brand: Simplicity Pages: 10

Brand: Prorack Pages: 10

Brand: Beper Pages: 52

Brand: C-KO Pages: 4

Brand: Rugged Ridge Pages: 3

Brand: v.link Pages: 12

PRIME DESIGN HXR-269-E-UM3-80

Brand: Safe Fleet Pages: 12

OPTIA hybrid 2020

Brand: Kia Pages: 54

Brand: Axxess Pages: 16

Brand: EUFAB Pages: 4

Brand: Datsun Pages: 104

Brand: Haltech Pages: 12

Brand: Audiovox Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands