Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 320 | Manualshive

Page: 320 / 922

background image

Verification Tests

ABS VERIFICATION TEST - VER 1

APPLICABILITY

1. Turn the ignition off.
2. Connect all previously disconnected components and connectors.
3. Ensure all accessories are turned off and the battery is fully charged.
4. Ensure that the Ignition is on, and with the DRBIII, erase all Diagnostic Trouble Codes from
ALL modules. Start the engine and allow it to run for 2 minutes and fully operate the system
that was malfunctioning.
5. Turn the ignition off and wait 5 seconds. Turn the ignition on and using the DRBIII, read
DTC’s from ALL modules.
6. If any Diagnostic Trouble Codes are present, return to Symptom list and troubleshoot new
or recurring symptom.
7. NOTE: For Sensor Signal and Pump Motor faults, the CAB must sense all 4 wheels
at 25 km/h (15 mph) before it will extinguish the ABS Indicator.
8. If there are no DTC’s present after turning ignition on, road test the vehicle for at least 5
minutes. Perform several antilock braking stops.
9. Caution: Ensure braking capability is available before road testing.
10. Again, with the DRBIII

t

read DTC’s. If any DTC’s are present, return to Symptom list.

11. If there are no Diagnostic Trouble Codes (DTC’s) present, and the customer’s concern can no
longer be duplicated, the repair is complete.
Are any DTC’s present or is the original concern still present?

All

Yes

→

Repair is not complete, refer to appropriate symptom.

No

→

Repair is complete.

38

VERIFICATION TESTS

«
...
318
319
320
321
322
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: Mazda Pages: 4

Brand: Jeep Pages: 6

Brand: Daihatsu Pages: 485

Green Motion DC 22

Brand: Eaton Pages: 65

Brand: Kathrein Pages: 7

Brand: Porsche Pages: 51

Brand: Whispbar Pages: 14

Brand: Whispbar Pages: 14

Brand: U.S. General Pages: 8

Brand: AEM Pages: 27

Brand: THIEYE Pages: 88

OPTIA hybrid 2020

Brand: Kia Pages: 54

MultiCharger 1204

Brand: DEFA Pages: 28

Brand: Steelmate Pages: 14

MagicSpeed MS900

Brand: Waeco Pages: 120

Brand: Dometic Pages: 24

F-250 Super Duty 2022

Brand: Ford Pages: 740

spectroFlex Car Adapter

Brand: wtw Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands