Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 810 | Manualshive

Page: 810 / 922

background image

TEST

ACTION

APPLICABILITY

7

Turn the ignition off to the lock position.
Disconnect the PCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance between ground and the LR Solenoid Control circuit.
Is the resistance below 5.0 ohms?

All

Yes

→

Repair the LR Solenoid Control circuit for a short to ground.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→

Go To

8

8

Turn the ignition off to the lock position.
Disconnect the PCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the voltage of the LR Solenoid Control circuit.
Is the voltage above 0.5 volts?

All

Yes

→

Repair the LR Solenoid Control circuit for a short to voltage.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→

Go To

9

9

Turn the ignition off to the lock position.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and Transmission Control Relay
Output circuit in the Transmission Control Relay connector.
Using a 12-volt test light connected to ground, check the Transmission Relay Output
circuit in the Transmission Solenoid/Pressure Switch harness connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

All

Yes

→

Go To

10

No

→

Repair the Transmission Control Relay Output circuit for an
open. If the fuse is open make sure to check for a short to ground.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

89

TRANSMISSION - NGC

P0750-LR SOLENOID CIRCUIT —

Continued

«
...
808
809
810
811
812
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: Accel Pages: 2

Brand: UnderCover Pages: 16

Titanium Series

Brand: Fass Pages: 13

Multiple G9F18 AU000

Brand: Genesis Pages: 3

Brand: Kia Pages: 54

Brand: Metra Electronics Pages: 2

Brand: Masterack Pages: 4

Brand: Over Armour Offroad Pages: 5

Brand: Thule Pages: 12

Brand: tams elektronik Pages: 44

Brand: Quadratec Pages: 12

Brand: Tachosys Pages: 28

Brand: Hella Pages: 21

Brand: Meta System Pages: 16

Brand: JSPORT Pages: 2

Brand: Bestop Pages: 4

Brand: Prorack Pages: 15

Brand: Subaru Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands