Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 42 | Manualshive

Page: 42 / 922

background image

TEST

ACTION

APPLICABILITY

2

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
Disconnect the Driver Airbag Module.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool to the Driver Airbag connectors.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
With the DRBIII

t

, read the active Airbag DTCs.

Does the DRBIII

t

show DRIVER SQUIB 1 SHORT TO GROUND?

All

Yes

→

Go To

3

No

→

Replace the Driver Airbag in accordance with the Service Infor-
mation.
Perform AIRBAG VERIFICATION TEST - VER 1.

3

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Clockspring connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool to the Clockspring connector.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
With the DRBIII

t

, read the active Airbag DTCs.

Does the DRBIII

t

show DRIVER SQUIB 1 SHORT TO GROUND?

All

Yes

→

Go To

4

No

→

Replace the Clockspring.
Perform AIRBAG VERIFICATION TEST - VER 1.

4

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Airbag Control Module connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool adaptor to the Airbag Control Module connector.
Disconnect the Load Tool from the Clockspring connector.
Measure the resistance of the Driver Squib 1 Line 1 and Line 2 circuits between
Clockspring connector and ground.
Is the resistance below 10K ohms on either circuit?

All

Yes

→

Repair Driver Squib 1 Line 1 or Line 2 circuits shorted to ground.
Perform AIRBAG VERIFICATION TEST - VER 1.

No

→

Replace the Airbag Control Module in accordance with Service
Instructions.
Perform AIRBAG VERIFICATION TEST - VER 1.

35

AIRBAG

DRIVER SQUIB 1 SHORT TO GROUND —

Continued

«
...
40
41
42
43
44
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: Acdeos Pages: 38

Brand: Lancia Pages: 386

Brand: Front Runner Pages: 5

1306 RAPID SYSTEM

Brand: Thule Pages: 8

Brand: Mercedes-Benz Pages: 30

Brand: Whispbar Pages: 15

Brand: EEZ RV Pages: 31

Quattroporte Automatic

Brand: Maserati Pages: 272

Brand: Yakima Pages: 13

Brand: Rugged Ridge Pages: 3

Hatch-bag Luggage System

Brand: Tabernus Peram Pages: 10

Brand: Motoalliance Pages: 4

Full Display Mirror

Brand: Gentex Pages: 18

530 GRAN TURISMO - 2010

Brand: BMW Pages: 26

1997 Park Avenue

Brand: Buick Pages: 420

Brand: Ranger design Pages: 6

Brand: Chevrolet Pages: 6

EPL7SAM+C Series

Brand: Pinnacle Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands