Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 805 | Manualshive

Page: 805 / 922

background image

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t

, read Transmission DTC’s.

If any of these DTC’s are present, perform their respective tests first.
Are there any Loss of Prime, Line Pressure Sensor and/or Speed Sensor DTCs
present?

All

Yes

→

Refer to the Transmission category and perform the appropriate
symptom. If any of these DTC’s are present, they will cause a gear
ratio error. Perform the test for Loss of Prime first if it is present.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→

Go To

3

3

With the DRBIII

t

, perform the Reverse Gear Clutch test. Follow the instructions on

the DRBIII

t

.

Increase the throttle angle or TPS Degree to 30° for no more than a few seconds.
CAUTION: Do not overheat the transmission.
Did the clutch test pass - Input Speed remain at zero?

All

Yes

→

Go To

4

No

→

Go To

5

4

The conditions to set this DTC are not current at this time.
Check the gearshift linkage adjustment.
Gear ratio DTC’s can be set by problems in the Input and Output Speed Sensor
circuits. If the vehicle passes the clutch test and still sets gear ratio DTC’s, check the
Speed Sensors for proper operation.
Remove the Starter Relay.
With the DRBIII

t

, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Check the Speed Sensor wiring and connectors for good connection, then perform a
wiggle test using the Transmission Simulator, Miller tool #8333 and Electronic
Transmission Adapter kit, Miller tool #8333-1.
This DTC can also be set under extreme temperature conditions, this is usually
caused by an internal problem. Verify if the problem is only experienced under
extreme hot or cold conditions.
With the DRBIII

t

, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Were there any problems found?

All

Yes

→

Repair as necessary.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→

Test Complete.

5

If there are no possible causes remaining, view repair.

All

Repair

Repair internal transmission per the Service Information. Check
all of the components related to the Reverse and LR clutches.
Inspect the Oil Pump and repair or replace per the Service
Information.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

84

TRANSMISSION - NGC

P0736-GEAR RATIO ERROR IN REVERSE —

Continued

«
...
803
804
805
806
807
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: B-Speech Pages: 18

Brand: Doug Thorley Headers Pages: 5

Brand: Edelbrock Pages: 2

Brand: Motoalliance Pages: 8

Brand: Draw tite Pages: 4

Brand: Mercedes-Benz Pages: 329

2011 A3 Sportback

Brand: Audi Pages: 29

Brand: Magneti Marelli Pages: 2

Brand: v.link Pages: 21

Brand: Black Horse Off Road Pages: 7

Brand: r.LiNK Pages: 21

Brand: MAcarbon Pages: 3

Brand: Needit Pages: 2

KIT ParkingSensor 814

Brand: Gemini Pages: 6

Brand: Ford Pages: 585

Brand: Brigade Pages: 12

Brand: Westin Pages: 3

Brand: Whispbar Pages: 77

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands