Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 242 | Manualshive

Page: 242 / 922

background image

Verification Tests

40/41TE (NGC) TRANSMISSION VERIFICATION TEST - VER 1

APPLICABILITY

1. NOTE: After completion of the Transmission Verification Test, the Powertrain
Verification Test must be performed. Refer to the Powertrain Category.
2. Connect the DRBIII

t

to the Data Link Connector (DLC).

3. Reconnect any disconnected components.
4. With the DRBIII

t

, erase all Transmission DTC’s, also erase the PCM DTC’s.

5. Perform *PRNDL FAULT CLEARING PROCEDURE after completion of repairs for P0706
CHECK SHIFTER SIGNAL.
6. With the DRBIII

t

, display Transmission Temperature. Start and run the engine until the

Transmission Temperature is HOT, above 43° C or 110° F.
7. Check the transmission fluid and adjust if necessary. Refer to the Service Information for the
Fluid Fill procedure.
8. NOTE: If the Transmission Control Module or Torque Converter has been replaced,
or if the Transmission has been repaired or replaced, it is necessary to perform the
DRBIII

t

Quick Learn Procedure and reset the

(

Pinion Factor

(

.

9. Road test the vehicle. With the DRBIII

t

, monitor the engine RPM. Make 15 to 20 1-2, 2-3,

3-4 upshifts. Perform these shifts from a standing start to 45 MPH with a constant throttle
opening of 20 to 25 degrees.
10. Below 25 MPH, make 5 to 8 wide open throttle kickdowns to 1st gear. Allow at least 5
seconds each in 2nd and 3rd gear between each kickdown.
11. For a specific DTC, drive the vehicle to the Symptom’s When Monitored/When Set
conditions to verify the DTC is repaired.
12. If equipped with AutoStick

t

, upshift and downshift several times using the AutoStick

t

feature during the road test.
13. NOTE: Use the EATX OBDII task manager to run Good Trip time in each gear, this
will confirm the repair and to ensure that the DTC has not re-matured.
14. Check for Diagnostic Trouble Codes (DTC’s) during the road test. If a DTC sets during the
road test , return to the Symptom list and perform the appropriate symptom.
15. NOTE: Erase P0700 DTC in the PCM to turn the MIL light off after making
transmission repairs.
Were there any Diagnostic Trouble Codes set during the road test?

All

Yes

→

Repair is not complete, refer to the appropriate symptom.

No

→

Repair is complete.

235

VERIFICATION TESTS

«
...
240
241
242
243
244
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: Daihatsu Pages: 340

Brand: Camcar Pages: 6

Brand: Jeep Pages: 25

Brand: Jeep Pages: 51

Brand: Farenheit Pages: 8

Brand: RAM Pages: 116

Brand: Kia Pages: 385

Cherokee 16 1982

Brand: Jeep Pages: 1311

Brand: AC Schnitzer Pages: 16

Brand: TATA Motors Pages: 236

Polaris TATOU 4S

Brand: Camoplast Pages: 13

Brand: Hyundai Pages: 280

Brand: Toyota Pages: 636

Brand: Metra Electronics Pages: 8

Brand: VER-MAC Pages: 64

Brand: Mobility Networks Pages: 52

Brand: Cadillac Pages: 2

Brand: Buick Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands