Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 87 | Manualshive

Page: 87 / 922

background image

TEST

ACTION

APPLICABILITY

2

WARNING: TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT
TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED SEAT BACK PAD-
DED SIDE DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL
INTO THE AIR IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN
SERIOUS OR FATAL INJURY.
Disconnect the Seat Airbag connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool to the Seat Airbag connector.
WARNING: TURN IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRBIII

t

, read SIACM active DTC’s.

Does the DRBIII

t

display SEAT SQUIB SHORT TO GROUND?

All

Yes

→

Go To

3

No

→

Replace the Seat Airbag in accordance with Service Instructions.
Perform AIRBAG VERIFICATION TEST - VER 1.

3

WARNING: TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT
TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED SEAT BACK PAD-
DED SIDE DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL
INTO THE AIR IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN
SERIOUS OR FATAL INJURY.
Disconnect the Airbag Load Tool Jumper.
Disconnect the Side Impact Airbag Control Module connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool SIACM adaptor to the SIACM connector.
Measure the resistance of the Seat Squib Line 1 and Line 2 circuits between the
Curtain Squib connector and ground.
Is the resistance below 10K ohms on either circuit?

All

Yes

→

Repair Seat Squib Line 1 or Line 2 shorted to ground.
Perform AIRBAG VERIFICATION TEST - VER 1.

No

→

Replace the Side Impact Airbag Control Module in accordance
with Service Instructions. WARNING: IF THE SIDE IMPACT
AIRBAG CONTROL MODULE IS DROPPED AT ANY TIME, IT
MUST BE REPLACED.
Perform AIRBAG VERIFICATION TEST - VER 1.

80

AIRBAG

SEAT SQUIB SHORT TO GROUND —

Continued

«
...
85
86
87
88
89
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: Yakima Pages: 8

Brand: kincrome Pages: 6

Brand: Pyle Pages: 4

FIX&GO automatic

Brand: Alfa Romeo Pages: 40

Brand: U.S. General Pages: 4

Quattroporte Automatic

Brand: Maserati Pages: 272

Brand: AC Schnitzer Pages: 16

Brand: RAM Pages: 76

Brand: Advantech Pages: 59

Brand: Icom Pages: 20

Brand: Kuda Pages: 2

DAF CHARGEMAX 90

Brand: Paccar Pages: 40

1966 Spider 105

Brand: Alfa Romeo Pages: 46

Brand: Thule Pages: 12

Brand: Kia Pages: 680

Brand: Xforce Pages: 11

Halo Pole Mount

Brand: Charge Amps Pages: 14

Brand: Mazda Pages: 605

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands