manualshive.com logo in svg

Dodge 2004 Neon SRT4, Diagnostic Manual

Get your hands on the Dodge 2004 Neon SRT4 Diagnostic Manual for free download. This essential manual provides detailed information on diagnosing and troubleshooting your vehicle. Download it now from manualshive.com to ensure your SRT4 stays running smoothly.

Share
Download
background image

TEST

ACTION

APPLICABILITY

1

NOTE: Diagnose any TP Sensor or MAP Sensor component DTCs before
continuing.
NOTE: If the P0501 - No Vehicle Speed Signal is set along with this DTC,
refer to the P0501 diagnostics before continuing.
NOTE: The throttle plate and linkage must be free from binding and carbon
build up, ensure the throttle plate is at the idle position, ensure the throttle
plate is at the idle position.
Ignition on, engine not running.
With the DRBIII

t

, read DTCs and record the related Freeze Frame data.

Is the Good Trip Counter displayed and equal to zero?

All

Yes

→

Go To

2

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

2

NOTE: This code is intended to shut down the engine if a large crack occurs
in the intake manifold.
NOTE: A large vacuum leak is most likely the cause of this DTC.
Inspect the Intake Manifold for leaks and cracks.
Inspect the Power Brake Booster for any vacuum leaks.
Inspect the PCV system for proper operation or any vacuum leaks.
Were any vacuum leaks found?

All

Yes

→

Repair the vacuum leak as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

3

3

Start the engine.
With the DRBIII

t

, monitor the MAP Sensor voltage.

Snap the throttle from wide open throttle to idle several times.
Does the MAP Sensor voltage vary from below 2.0 volts at idle to above 3.5 volts?

All

Yes

→

Go To

4

No

→

Go To

12

4

Ignition on, engine not running.
With the DRBIII

t

, monitor the TP Sensor voltage while slowly depressing the

throttle pedal from the idle position to the wide open throttle position.
Does the voltage start approximately at 0.8 volts and go above 3.5 volts with a smooth
transition?

All

Yes

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

5

271

DRIVEABILITY - NGC

P2074-MANIFOLD PRESSURE/THROTTLE POSITION CORRELATION -
HIGH FLOW/VACUUM LEAK —

Continued

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

RAM 2015 1500 User Manual preview
2015 1500
Brand: RAM Pages: 292
RAM Trucks 1500 User Manual preview
Trucks 1500
Brand: RAM Pages: 116
Farad BARS PR25 - 2 Quick Start Manual preview
BARS PR25 - 2
Brand: Farad Pages: 8
VDO DLD Wide Range II Installation Instructions Manual preview
DLD Wide Range II
Brand: VDO Pages: 84
Wagan TravelCharge Companion GO-Plus User Manual preview
TravelCharge Companion GO-Plus
Brand: Wagan Pages: 3
EZTRUNK PHANTOM JK Assembly Manual preview
PHANTOM JK
Brand: EZTRUNK Pages: 3
Anker Technology Roav VIVA Owner'S Manual preview
Roav VIVA
Brand: Anker Technology Pages: 8
Oldsmobile 1994 Bravada Owner'S Manual preview
1994 Bravada
Brand: Oldsmobile Pages: 248
Jaeger 12160509J Fitting Instructions Manual preview
12160509J
Brand: Jaeger Pages: 16
Whispbar K684W Fitting Instructions Manual preview
K684W
Brand: Whispbar Pages: 15
Master Tailgaters MR-43E2DVR1 User Manual preview
MR-43E2DVR1
Brand: Master Tailgaters Pages: 10
Acura TSX 2014 Advanced Technology Manual preview
TSX 2014
Brand: Acura Pages: 19
Ford 2009 Edge Owner'S Manual preview
2009 Edge
Brand: Ford Pages: 325
GMC 2008 Savana Van Owner'S Manual preview
2008 Savana Van
Brand: GMC Pages: 402
Easee Base 1-Way User Manual / Installation Manual preview
Base 1-Way
Brand: Easee Pages: 21
Uniden BTSC1100 Owner'S Manual preview
BTSC1100
Brand: Uniden Pages: 16
Metra Electronics 99-7804 Installation Instructions Manual preview
99-7804
Brand: Metra Electronics Pages: 10
Phonocar 6/946 Instruction Manual preview
6/946
Brand: Phonocar Pages: 4

Brands by name

Popular brands

Load more brands