Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 52 | Manualshive

Page: 52 / 922

background image

TEST

ACTION

APPLICABILITY

4

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Airbag Control Module connector.
NOTE: Check connectors - Clean and repair as necessary.
Measure the resistance of the Fused Ignition Switch Output Run circuit between the
ACM connector and ground.
Is the resistance below 10K ohms ?

All

Yes

→

Repair the Fused Ignition Switch Output Run circuit for a short
to ground and replace Airbag Run Fuse.
Perform AIRBAG VERIFICATION TEST - VER 1.

No

→

Go To

5

5

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE
PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
If there are no possible causes remaining, view repair.

All

Repai:

Replace the Airbag Control Module in accordance with Service
Instructions and replace the Run Only Fuse.
Perform AIRBAG VERIFICATION TEST - VER 1.

NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.

6

Turn the ignition on.
Measure the voltage of the Ignition Switch Output Run circuit between the Airbag
Run circuit fuse and ground.
Is the voltage above approximately 4.5 volts?

All

Yes

→

Go To

7

No

→

Repair the open Ignition Switch Output Run circuit.
Perform AIRBAG VERIFICATION TEST - VER 1.

7

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Airbag Control Module connector.
NOTE: Check connectors - Clean and repair as necessary.
Reinstall the airbag Run fuse.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
Measure the voltage of the Fused Ignition Switch Output Run circuit at the Airbag
Control Module connector.
Is the voltage above approximately 4.5 volts?

All

Yes

→

Go To

8

No

→

Repair the an open or high resistance in the Fused Ignition
Switch Output Run circuit.
Perform AIRBAG VERIFICATION TEST - VER 1.

45

AIRBAG

LOSS OF IGNITION RUN ONLY —

Continued

«
...
50
51
52
53
54
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: cam Pages: 2

Brand: Dapper Lighting Pages: 2

Brand: Metra Electronics Pages: 2

Brand: Cadillac Pages: 402

Brand: Cobra Pages: 2

51 47 0 027 792

Brand: BMW Pages: 7

Brand: Ford Pages: 728

Brand: Westin Pages: 5

Brand: Weltmann KFZ-Teile Pages: 12

Brand: Mercedes-Benz Pages: 10

Brand: Scosche Pages: 32

Black Bison Sports Series

Brand: Wald Pages: 7

Brand: Navman Pages: 27

Brand: Mazda Pages: 7

Brand: Stack Pages: 4

Brand: Chipolino Pages: 11

CITY GO PD349056A

Brand: Baby Jogger Pages: 16

Brand: Saab Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands