Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 501 | Manualshive

Page: 501 / 922

background image

TEST

ACTION

APPLICABILITY

6

Reconnect all vacuum hoses.
Start the engine.
Allow the engine to idle.
Using the DRBIII

t

, perform the NVLD FORCED MONITOR TEST.

Monitor the NVLD Switch.
As the test runs, the NVLD Switch should go from an OPEN state to
CLOSED. After the vacuum is released form the EVAP system the Switch
state will return to OPEN.
Did the NVLD Switch operate as described above?

All

Yes

→

Go To

7

No

→

Replace the NVLD Assembly.
Perform POWERTRAIN VERIFICATION TEST VER - 6 - NGC.

7

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Review the DRBIII

t

Freeze Frame information. If possible, try to duplicate the

conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
NOTE: A loose gas cap could have caused this DTC to set. Make sure gas cap
is tight and in good condition. Ensure the gas cap meets OEM specifications.
Perform a visual and physical inspection of the entire Evaporative Emission system.
Check for the following conditions:
- Holes or cracks
- Loose seal points
- Evidence of damaged components
- Incorrect routing of hoses and tubes
- Fuel Cap gasket seal
Were any of the above conditions found?

All

Yes

→

Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 6 - NGC.

No

→

Test Complete.

165

DRIVEABILITY - NGC

P0442-EVAP SYSTEM MEDIUM LEAK —

Continued

«
...
499
500
501
502
503
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: OEM Tools Pages: 4

Brand: Oldsmobile Pages: 360

Brand: AC Schnitzer Pages: 16

Brand: B-Speech Pages: 4

Brand: Paser Pages: 2

Brand: Xblitz Pages: 56

Interlock 700 Series

Brand: Scania Pages: 82

Brand: J. Strong Pages: 2

Brand: Jeep Pages: 374

Brand: TracRac Pages: 6

Gigaware 12-493

Brand: Gigaware Pages: 8

Brand: Mazda Pages: 196

Brand: Skoda Pages: 288

Brand: ICON Pages: 4

PerfectView CRT300

Brand: Waeco Pages: 200

650i Convertible

Brand: BMW Pages: 256

Brand: PAC Pages: 7

Brand: Kia Pages: 828

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands