Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 477 | Manualshive

Page: 477 / 922

background image

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t

, read and record Freeze Frame Data specific to the CKP signal,

ECT, RPM, Sync state, vehicle speed, etc.
Turn the ignition off.
With the DRBIII

t

lab scope probe and the Miller special tool #6801, backprobe the

(K24) CKP Signal circuit at the Sensor harness connector.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Ignition on, engine not running.
Observe the lab scope screen at least 1 minute and then start the vehicle.
Continue observing the lab scope screen for an additional minute.
Were there any irregular or missing signals?

All

Yes

→

Go To

3

No

→

Go To

8

3

Visually inspect the related wire harness including the ground circuit. Look for any
chafed, pierced, pinched, or partially broken wires.
Visually inspect the related wire harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Ensure the Crankshaft Position Sensor and the Camshaft Position Sensor are
properly installed and the mounting bolt(s) are tight.
Refer to any TSBs that may apply.
Were any of the above conditions present?

All

Yes

→

Repair as necessary
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

4

4

Turn the ignition off.
Disconnect the CKP Sensor connector.
Ignition on, engine not running.
Measure the voltage on the (K7) 5 Volt Supply circuit.
Is the voltage between 4.5 and 5.5 volts?

All

Yes

→

Go To

5

No

→

Repair the open or short to ground in the (K7) 5 Volt Supply
circuit. Use Miller special tool #8815 when checking for an open
circuit to prevent PCM harness connector terminal damage.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

5

Turn the ignition off.
Carefully disconnect the Battery (-) Ground cable.
Remove the Crankshaft Position Sensor.
Inspect the Tone Wheel/Flex Plate slots for damage, foreign material, or excessive
movement.
Were any problems found?

All

Yes

→

Repair or replace the Tone Wheel/Flex Plate as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

6

141

DRIVEABILITY - NGC

P0339-CRANKSHAFT POSITION SENSOR INTERMITTENT —

Continued

«
...
475
476
477
478
479
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: Q'STRAINT Pages: 10

Brand: Triumph Pages: 86

Brand: Conrad Pages: 26

2003 Thunderbird

Brand: Ford Pages: 200

Brand: Mobis Pages: 16

Brand: Subaru Pages: 216

Brand: Dometic GROUP Pages: 20

Brand: FormFit Pages: 2

Brand: FormFit Pages: 4

PACCAR PACMOBILE 20

Brand: DAF Pages: 18

Brand: XTC Pages: 4

Brand: Veigel Pages: 24

Brand: Cellular Line Pages: 25

Brand: Van Guard Pages: 3

Brand: Jaeger Pages: 17

STO N SHO SNS 144

Brand: Big Mikes Performance Parts Pages: 7

Brand: Lincoln Pages: 10

Brand: Yakima Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands