Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 116 | Manualshive

Page: 116 / 922

background image

Symptom:

*NO RESPONSE FROM PCM (PCI BUS) - NGC

POSSIBLE CAUSES

PCM PCI NO RESPONSE

POWERTRAIN CONTROL MODULE

PCI BUS CIRCUIT OPEN

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
NOTE: As soon as one or more module communicates with the DRB, answer
the question.
With the DRB, enter Anti-Lock Brakes.
With the DRB, enter Electro/Mechanical Cluster (MIC).
With the DRB, enter Passive Restraints then Airbag.
Were you able to establish communications with any of the modules?

All

Yes

→

Go To

2

No

→

Refer to symptom PCI Bus Communication Failure in the Com-
munications category.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

2

With the DRB read the Powertrain DTC’s. This is to ensure power and grounds to the
PCM are operational.
NOTE: If the DRB will not read PCM DTC’s, follow the NO RESPONSE TO
PCM (PCM SCI only) symptom path.
Turn the ignition off.
Disconnect the PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and
black test probes.
Connect the scope input cable to the channel one connector on the DRB. Attach the
red and black leads and the cable to probe adapter to the scope input cable.
With the DRBIII

t

select Pep Module Tools.

Select lab scope.
Select Live Data.
Select 12 volt square wave.
Press F2 for Scope.
Press F2 and use the down arrow to set voltage range to 20 volts. Press F2 again
when complete.
Connect the Black lead to the chassis ground. Connect the Red lead to the PCI Bus
circuit in the appropriate terminal of special tool #8815.
Turn the ignition on.
Observe the voltage display on the DRB Lab Scope.
Does the voltage pulse from 0 to approximately 7.5 volts?

All

Yes

→

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

→

Repair the PCI Bus circuit for an open.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

109

COMMUNICATION

«
...
114
115
116
117
118
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: cam Pages: 28

STRONGARM RVR303

Brand: Blue Giant Pages: 48

Brand: Ford Pages: 22

Brand: Mitsubishi Pages: 19

Brand: Volvo Pages: 123

ESCALADE ESV 2005

Brand: Cadillac Pages: 482

Brand: curt Pages: 4

Brand: true-i Pages: 11

CERTA CTCVINCVR14A

Brand: Kogan Pages: 4

Brand: Volvo Pages: 362

T13 Outback Frontal Protection System

Brand: T.J.M. Pages: 18

Brand: Audi Pages: 4

Sprinter Bed System DIY

Brand: FVC Pages: 8

Brand: BMW Pages: 278

Brand: Buick Pages: 112

Brand: Airstream Pages: 103

Brand: Volvo Pages: 304

Brand: Haltech Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands