Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 448

Page: 448 / 922

Symptom List:

P0201-FUEL INJECTOR #1
P0202-FUEL INJECTOR #2
P0203-FUEL INJECTOR #3
P0204-FUEL INJECTOR #4

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P0201-FUEL INJECTOR #1.

When Monitored and Set Condition:

P0201-FUEL INJECTOR #1

When Monitored:

With battery voltage greater than 10 volts. Auto Shutdown Relay

energized. Engine speed less than 3000 rpm.

Set Condition:

No inductive spike is detected after injector turn off. One Trip Fault.

P0202-FUEL INJECTOR #2

When Monitored:

With battery voltage greater than 10 volts. Auto Shutdown Relay

energized. Engine speed less than 3000 rpm.

Set Condition:

No inductive spike is detected after injector turn off. One Trip Fault.

P0203-FUEL INJECTOR #3

When Monitored:

With battery voltage greater than 10 volts. Auto Shutdown Relay

energized. Engine speed less than 3000 rpm.

Set Condition:

No inductive spike is detected after injector turn off. One Trip Fault.

P0204-FUEL INJECTOR #4

When Monitored:

With battery voltage greater than 10 volts. Auto Shutdown Relay

energized. Engine speed less than 3000 rpm.

Set Condition:

No inductive spike is detected after injector turn off. One Trip Fault.

POSSIBLE CAUSES

GOOD TRIP EQUAL TO ZERO

ASD RELAY OUTPUT CIRCUIT

FUEL INJECTOR

INJECTOR CONTROL CIRCUIT OPEN

INJECTOR CONTROL CIRCUIT SHORTED TO GROUND

PCM

112

DRIVEABILITY - NGC

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2004 Neon SRT4

Reviews:

Related manuals for 2004 Neon SRT4

Brands by name

Popular brands

Dodge 2004 Neon SRT4, Diagnostic Manual

Search results

Summary of Contents for 2004 Neon SRT4

Reviews:

Related manuals for 2004 Neon SRT4

Brands by name

Popular brands