Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 456 | Manualshive

Page: 456 / 922

background image

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the Wastegate Solenoid harness connector.
Using a 12-volt test light connected to battery voltage, probe the (Z1) Ground circuit
in the Wastegate harness connector.
Does the test light illuminate brightly?

All

Yes

→

Go To

4

No

→

Repair the (Z1) Ground circuit for an open.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

4

NOTE: The Wastegate Sol Control circuit is a high side control circuit. When
the circuit is operating normally voltage will be present.
Turn the ignition off.
Disconnect the Wastegate Solenoid harness connector.
Disconnect the PCM harness connectors.
Turn the ignition on
Measure the voltage of the (K137) Wastegate Sol Control circuit in the Wastegate
Solenoid harness connector.
Does the voltmeter indicate any voltage present?

All

Yes

→

Repair the short to voltage in the (K137) Wastegate Sol Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

5

5

Turn the ignition off.
Disconnect the Wastegate Solenoid harness connector.
Disconnect the PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K137) Wastegate Sol Control circuit from the
Wastegate Solenoid harness connector to the appropriate terminal of special tool
#8815.
Is the resistance below 5.0 ohms?

All

Yes

→

Go To

6

No

→

Repair the open in the (K137) Wastegate Sol Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

6

Turn the ignition off.
Disconnect the Wastegate Solenoid harness connector.
Disconnect the PCM harness connectors.
Measure the resistance between ground and the (K137) Wastegate Sol Control circuit
at the Wastegate Solenoid harness connector.
Is the resistance below 100 ohms?

All

Yes

→

Repair the short to ground in the (K137) Wastegate Sol Control
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

7

120

DRIVEABILITY - NGC

P0243-WASTEGATE SOLENOID CIRCUIT —

Continued

«
...
454
455
456
457
458
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: JASTEC Pages: 12

Brand: Axxess Pages: 4

Brand: Vintage Air Pages: 14

Brand: DEFA Pages: 7

Brand: Prorack Pages: 15

Porsche 911 GT3 R

Brand: iRacing Pages: 25

Brand: EZTRUNK Pages: 3

Brand: Metra Electronics Pages: 8

Brand: Hyundai Pages: 18

Brand: Camecho Pages: 2

E60-82-007-02-10

Brand: Eibach Pages: 3

Brand: Huf Pages: 6

Brand: true-i Pages: 11

Brand: Oldsmobile Pages: 276

Brand: Volkswagen Pages: 32

Brand: Subaru Pages: 399

Brand: EUFAB Pages: 12

Brand: JBA Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands