Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 213 | Manualshive

Page: 213 / 922

background image

Symptom:

*DRIVER DOOR FAILS TO LOCK & UNLOCK

POSSIBLE CAUSES

RKE MODULE - OPEN DRIVER UNLOCK CIRCUIT

DRIVER DOOR LOCK MOTOR - OPEN

DRIVER DOOR LOCK RELAY OUTPUT WIRE OPEN

DRIVER DOOR UNLOCK RELAY OUTPUT WIRE OPEN

TEST

ACTION

APPLICABILITY

1

Disconnect the Remote Keyless Entry module connector.
Lower the driver door window.
Connect a jumper wire between the Door Lock Relay Output ckt and the Ground ckt
in the RKE module connector.
Connect a jumper wire to the Driver Door Unlock Relay Output ckt and momentarily
touch it to the Fused B(+) ckt and observe the door lock.
Reverse the jumper wires to drive the motor in the opposite direction.
Did the drivers door Lock and Unlock?

All

Yes

→

Replace the Remote Keyless Entry Module.
Perform BODY VERIFICATION TEST - VER 1.

No

→

Go To

2

2

Ensure the RKE module is connected before proceeding.
Remove the inner door trim panel to gain access to the Door Lock Motor connector.
Disconnect the Door Lock Motor connector.
Connect a test light between the Door Lock Relay Output and the Driver Door Unlock
Relay Output circuits in the door lock motor connector.
Press the door lock switch to the Lock and Unlock positions.
Did the test light illuminate when the lock switch was pressed in both directions?

All

Yes

→

Replace the Driver Door Lock Motor.
Perform BODY VERIFICATION TEST - VER 1.

No

→

Go To

3

3

Remove the inner door trim panel to gain access to the Door Lock Motor connector.
Disconnect the Door Lock Motor connector.
Disconnect the Remote Keyless Entry module connector.
Measure the resistance of the Door Lock Relay Output wire between the RKE
connector and the door lock motor connector.
Is the resistance below 5.0 ohms?

All

Yes

→

Go To

4

No

→

Repair the Driver Door Lock Relay Output Wire for an open.
Perform BODY VERIFICATION TEST - VER 1.

206

POWER DOOR LOCKS/RKE

«
...
211
212
213
214
215
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: Lancia Pages: 191

Brand: PAC Pages: 15

Brand: RAM Pages: 20

CHASSIS CAB 3500 2017

Brand: RAM Pages: 16

Brand: Porsche Pages: 195

Brand: Mercedes-Benz Pages: 30

Brand: Actia Pages: 37

DELTA DL FIX 209FP

Brand: Menabo Pages: 8

Brand: PAC Pages: 14

Brand: Kolpin Pages: 3

Brand: Skoda Pages: 281

Brand: Daesung Pages: 9

Brand: Pontiac Pages: 318

Brand: r.LiNK Pages: 21

Brand: Volvo Pages: 10

Brand: Mopar Pages: 17

Brand: Kia Pages: 233

Brand: Mercedes-Benz Pages: 585

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands