Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 449 | Manualshive

Page: 449 / 922

background image

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t

, read DTCs and record the related Freeze Frame data.

Is the Good Trip Counter displayed and equal to zero?

All

Yes

→

Go To

2

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

2

Turn the ignition off.
Disconnect the Fuel Injector harness connector.
Ignition on, engine not running.
With the DRBIII

t

, actuate the ASD Relay.

Using a 12-volt test light connected to ground, backprobe the ASD Relay Output
circuit at the Fuel Injector harness connector.
Does the test light illuminate brightly?

All

Yes

→

Go To

3

No

→

Repair the open or high resistance in the ASD Relay Output
circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

3

Turn the ignition off.
Disconnect the Fuel Injector harness connector.
Ignition on, engine not running.
Using a 12-volt test light connected to 12-volts, backprobe the Injector Control
circuit.
With the DRBIII

t

, actuate the Fuel Injector.

Does the test light blink/flicker?

All

Yes

→

Replace the Fuel Injector.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

4

4

Turn the ignition off.
Disconnect the Fuel Injector harness connector.
Disconnect the PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the Injector Control circuit from the Fuel Injector harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

All

Yes

→

Go To

5

No

→

Repair the open in the Injector Control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

113

DRIVEABILITY - NGC

P0201-FUEL INJECTOR #1 —

Continued

«
...
447
448
449
450
451
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

SP200 - QUICKSTART GUIDE 1

Brand: Jabra Pages: 2

BT150 - Headset - Over-the-ear

Brand: Jabra Pages: 2

CHASSIS CAB 3500 2017

Brand: RAM Pages: 16

Brand: GATmatic Pages: 13

Brand: TrailFX Pages: 6

WrapAround Windjammer

Brand: Bestop Pages: 7

CB-796IG2-CIGD-R

Brand: CARRYBOY Pages: 4

Brand: GMC Pages: 428

Brand: Webasto Pages: 18

2014 Grand Cherokee SRT8

Brand: Jeep Pages: 596

Brand: Skoda Pages: 4

Brand: Ford Pages: 256

Brand: Maserati Pages: 302

Brand: Volvo Pages: 123

Brand: Ford Pages: 40

Brand: GYS Pages: 32

Brand: Vauxhall Pages: 4

Brand: ULTIMATE SPEED Pages: 132

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands