Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 295 | Manualshive

Page: 295 / 922

background image

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the CAB harness connector.
Using a 12-volt test light connected to 12-volts, probe the CAB harness connector
ground circuits.
Did the test light illuminate?

All

Yes

→

Go To

4

No

→

Repair the CAB Ground circuit for an open.
Perform ABS VERIFICATION TEST - VER 1.

4

Turn the ignition off.
Disconnect the CAB harness connector.
Using a 12-volt test light connected to ground, probe the ABS Valve Fused B(+) circuit
at the CAB harness connector.
Did the test light illuminate?

All

Yes

→

Go To

5

No

→

Repair the ABS Valve Fused B(+) circuit for an open.
Perform ABS VERIFICATION TEST - VER 1.

5

Turn the ignition off.
Disconnect the CAB harness connector.
Using a 12-volt test light connected to ground, probe the ABS Pump Fused B(+)
circuit at the CAB harness connector.
Did the test light illuminate?

All

Yes

→

Replace the Controller Antilock Brake in accordance with the
Service Information.
Perform ABS VERIFICATION TEST - VER 1.

No

→

Repair the ABS Pump Fused B(+) circuit for an open.
Perform ABS VERIFICATION TEST - VER 1.

6

Turn the ignition off.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wire harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Refer to any Hotline letters or Technical Service Bulletins that may apply.
Were any problems found?

All

Yes

→

Repair as necessary.
Perform ABS VERIFICATION TEST - VER 1.

No

→

Test Complete.

13

BRAKES (CAB)

CAB INTERNAL FAILURE —

Continued

«
...
293
294
295
296
297
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: Toyota Pages: 529

Brand: HALE Pages: 44

Brand: Jabra Pages: 2

Brand: Jabra Pages: 38

Brand: Honda Pages: 73

Brand: Neuspeed Pages: 2

Brand: Suzuki Pages: 353

Brand: Torklift Pages: 16

Brand: Metra Electronics Pages: 5

Brand: Renkforce Pages: 4

Alloy Rugged Ridge X-Clamp

Brand: Omix-Ada Pages: 2

Brand: Dodge Pages: 3

Brand: Softride Pages: 4

Brand: TEINHOF Pages: 2

Brand: Cadillac Pages: 438

Brand: STO N SHO Pages: 7

Brand: MBW Pages: 40

CommCenter 300MB-SD

Brand: Federal Signal Corporation Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands