Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 782 | Manualshive

Page: 782 / 922

background image

TEST

ACTION

APPLICABILITY

3

With the DRBIII

t

, Check the STARTS SINCE SET counter for P0714.

NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less?

All

Yes

→

Go To

4

No

→

Go To

7

4

Turn the ignition off to the lock position.
Remove the Starter Relay.
CAUTION: Removal of the Starter Relay is to prevent a Transmission, NO
RESPONSE, condition and disable the starter.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
With the Transmission Simulator, turn the Input/Output switch to OFF.
With the DRBIII

t

, monitor the TRANS TEMP VOLTS while turning the Thermistor

Voltage switch to all three positions on the Transmission Simulator.
Compare the DRBIII

t

readings with the numbers listed on the Transmission

Simulator.
Do the readings on the Transmission Simulator match a non-fluctuating DRBIII

t

reading ± 0.2 volts?

All

Yes

→

Go To

5

No

→

Go To

6

5

If there are no possible causes remaining, view repair.

All

Repair

Replace Transmission Solenoid/TRS assembly per the Service
Information.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

6

Using the schematics as a guide, inspect the wiring and connectors. Repair as
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Powertrain Control Module per the Service Informa-
tion. WITH THE DRBIII

t

PERFORM QUICK LEARN

Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

7

The conditions necessary to set this DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wires while checking for shorted and open circuits.
With the DRBIII

t

, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Were there any problems found?

All

Yes

→

Repair as necessary.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→

Test Complete.

61

TRANSMISSION - NGC

P0714-TRANSMISSION TEMPERATURE SENSOR INTERMITTENT —

Continued

«
...
780
781
782
783
784
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: Yakima Pages: 6

Brand: Yakima Pages: 18

Brand: Kia Pages: 54

Brand: Metra Electronics Pages: 2

10-8002-C11998B

Brand: Saleen Pages: 12

2013 Buick Verano

Brand: Buick Pages: 5

Stratus LHD 1997

Brand: Chrysler Pages: 1534

Brand: Mazda Pages: 13

Brand: Ford Pages: 368

Hypercharger HYC 075

Brand: Alpitronic Pages: 64

Evo All THAR-FOR3

Brand: Fortin Pages: 7

Brand: ACV Pages: 2

Brand: KEKO Pages: 3

Brand: Movon Pages: 43

Brand: Warn Pages: 5

Brand: ULTIMATE SPEED Pages: 40

Brand: Mitsubishi MOTORS Pages: 416

S90 - ACCESSORY PANEL

Brand: Volvo Pages: 166

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands