Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 813 | Manualshive

Page: 813 / 922

background image

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t

, read Transmission DTC’s

Are there any Transmission Control Relay DTC’s present also?

All

Yes

→

Refer to the Transmission category and perform the appropriate
symptom.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→

Go To

3

3

With the DRBIII

t

, Check the STARTS SINCE SET counter for P0755.

NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter set at 0?

All

Yes

→

Go To

4

No

→

Go To

11

4

Turn the ignition off to the lock position.
Remove the Starter Relay.
CAUTION: Removal of the Starter Relay is to prevent a Transmission, NO
RESPONSE, condition and disable the starter.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Ignition on, engine not running.
With the DRBIII

t

, actuate the 2/4 Solenoid.

With the Transmission Simulator, monitor the 2/4 Solenoid LED.
Did the 2/4 Solenoid LED on the Transmission Simulator blink on and off during
actuation?

All

Yes

→

Go To

5

No

→

Go To

6

5

If there are no possible causes remaining, view repair.

All

Repair

Replace the Transmission Solenoid/Pressure Switch Assembly per
the Service Information.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

6

Turn the ignition off to the lock position.
Disconnect the PCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the 2/4 Solenoid Control circuit from the appropriate
terminal of special tool #8815 to the Solenoid/Pressure Switch Assembly harness
connector.
Is the resistance above 5.0 ohms?

All

Yes

→

Repair the 2-4 Solenoid Control circuit for an open.
Perform 41TE (NGC) TRANSMISSION VERIFICATION TEST -
VER 1.

No

→

Go To

7

92

TRANSMISSION - NGC

P0755-2/4 SOLENOID CIRCUIT —

Continued

«
...
811
812
813
814
815
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: Mazda Pages: 4

Sterling ALL-TERRAIN 576

Brand: Roadmaster Pages: 12

Brand: Kia Pages: 10

Brand: CITROËN Pages: 301

Brand: Opel Pages: 254

Brand: Würth Pages: 36

PRIME DESIGN VBI-FT21B

Brand: Safe Fleet Pages: 12

Plusone Console 4521011B

Brand: Honda Pages: 4

Brand: Gator Pages: 8

Brand: benbat Pages: 14

Brand: SPL Pages: 5

BEDXTENDER HD MAX 74841-00A

Brand: AMP Research Pages: 9

Brand: Belkin Pages: 2

Brand: Thule Pages: 12

Brand: Oldsmobile Pages: 380

Brand: Audi Pages: 63

Brand: S&B Filters Pages: 4

Brand: Mazda Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands