Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 610 | Manualshive

Page: 610 / 922

background image

TEST

ACTION

APPLICABILITY

13

Turn the ignition off.
Disconnect the MAP Sensor harness connector.
Disconnect the PCM harness connector.
Measure the resistance between ground and the (K7) 5 volt Supply circuit at the
MAP Sensor harness connector.
Is the resistance above 100k ohms?

All

Yes

→

Go To

14

No

→

Repair the short to ground in the (K7) 5 volt Supply circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

14

Turn the ignition off.
Disconnect the MAP Sensor harness connector.
With the DRBIII

t

, monitor the MAP Sensor voltage.

Ignition on, engine not running.
Connect a jumper wire between the (K1) MAP Sensor Signal circuit and the (K4)
Sensor ground circuit .
Cycle the ignition switch from off to on.
With the DRBIII

t

, monitor the MAP Sensor voltage.

Does the DRBIII

t

display MAP voltage from approximately 4.9 volts to below 0.5

volt?

All

Yes

→

Replace the MAP Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

15

15

Turn the ignition off.
Disconnect the MAP Sensor harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K1) MAP Signal circuit from the MAP Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

All

Yes

→

Go To

16

No

→

Repair the (K1) MAP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

16

Turn the ignition off.
Disconnect the MAP Sensor harness connector.
Disconnect the PCM harness connector.
Measure the resistance between ground and the (K1) MAP Signal circuit at the MAP
Sensor harness connector.
Is the resistance above 100k ohms?

All

Yes

→

Go To

17

No

→

Repair the (K1) MAP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

274

DRIVEABILITY - NGC

P2074-MANIFOLD PRESSURE/THROTTLE POSITION CORRELATION -
HIGH FLOW/VACUUM LEAK —

Continued

«
...
608
609
610
611
612
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: Jeep Pages: 5

Brand: Jeep Pages: 6

Grand Cherokee SRT 2014

Brand: Jeep Pages: 345

Grand Cherokee 2015

Brand: Jeep Pages: 236

Brand: Jeep Pages: 18

Brand: Jeep Pages: 24

Brand: Jeep Pages: 560

Brand: Jeep Pages: 525

Brand: Jeep Pages: 308

Brand: Jeep Pages: 86

Brand: Jeep Pages: 638

Brand: Jeep Pages: 9

Brand: Jeep Pages: 51

Brand: Jeep Pages: 4

Brand: Jeep Pages: 50

Grand Cherokee SRT 2014

Brand: Jeep Pages: 118

2014 Grand Cherokee

Brand: Jeep Pages: 24

Brand: Jeep Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands