Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 369 | Manualshive

Page: 369 / 922

background image

TEST

ACTION

APPLICABILITY

7

Turn the ignition off.
With the DRBIII

t

lab scope probe and the Miller special tool #6801, backprobe the

(K24) CKP Signal circuit at the CKP harness connector.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Start the engine.
Observe the lab scope screen.
Are there any irregular or missing signals?

All

Yes

→

Go To

8

No

→

Go To

11

8

Visually inspect the related wire harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wire harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Ensure the Crankshaft Position Sensor and the Camshaft Position Sensor are
properly installed and the mounting bolt(s) tight.
Refer to any TSBs that may apply.
Were any of the above conditions present?

All

Yes

→

Repair as necessary
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

9

9

Turn the ignition off.
Remove the Crankshaft Position Sensor.
Inspect the Tone Wheel/Flex Plate slots for damage, foreign material, or excessive
movement.
Were any problems found?

All

Yes

→

Repair or replace the Tone Wheel/Flex Plate as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

10

10

If there are no possible causes remaining, view repair.

All

Repair

Replace the Crankshaft Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

33

DRIVEABILITY - NGC

P0016-CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT —

Continued

«
...
367
368
369
370
371
...
»

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 Neon SRT4

Brand: AC Schnitzer Pages: 16

Brand: Porsche Pages: 51

Brand: Whispbar Pages: 14

Brand: Subaru Pages: 99

Brand: WABCO Pages: 48

Brand: Yakima Pages: 21

Brand: Motoalliance Pages: 8

Brand: Sanitas Pages: 36

Brand: Motoalliance Pages: 5

Brand: Sagem Pages: 10

Brand: Aries Pages: 5

Brand: Mercedes-Benz Pages: 354

Brand: Xpresskit Pages: 18

Brand: Thule Pages: 3

Brand: Caraudio-Systems Pages: 9

Brand: JSPORT Pages: 2

FXX ATM Emulator

Brand: BMW Pages: 5

Brand: Hama Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands