Dodge 2004 Neon SRT4 Diagnostic Manual Download Page 371

Page: 371 / 922

Symptom List:

P0031-O2 SENSOR 1/1 HEATER CIRCUIT LOW
P0037-O2 SENSOR 1/2 HEATER CIRCUIT LOW

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P0031-O2 SENSOR 1/1 HEATER
CIRCUIT LOW.

When Monitored and Set Condition:

P0031-O2 SENSOR 1/1 HEATER CIRCUIT LOW

When Monitored:

Battery voltage above 10.6 volts, ASD is powered up, and O2 heater is

on.

Set Condition:

Desired state does not match Actual state.

P0037-O2 SENSOR 1/2 HEATER CIRCUIT LOW

When Monitored:

Battery voltage above 10.6 volts, ASD is powered up, and O2 heater is

on.

Set Condition:

Desired state does not match Actual state.

POSSIBLE CAUSES

O2 SENSOR HEATER OPERATION

O2 HEATER ELEMENT

O2 HEATER CONTROL CIRCUIT

O2 HEATER CONTROL SHORTED TO GROUND

PCM

TEST

ACTION

APPLICABILITY

Ignition on, engine not running.
With the DRBIII

, read DTCs and record the related Freeze Frame data.

Is the Good Trip Counter displayed and equal to zero?

All

Yes

→

Go To

→

Go To

DRIVEABILITY - NGC

Summary of Contents for 2004 Neon SRT4



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2004 Neon SRT4

Reviews:

Related manuals for 2004 Neon SRT4

Brands by name

Popular brands

Dodge 2004 Neon SRT4, Diagnostic Manual

Search results

Summary of Contents for 2004 Neon SRT4

Reviews:

Related manuals for 2004 Neon SRT4

Brands by name

Popular brands