Docomo N-04A, Instruction Manual

Page: 286 / 570

284
i-
α
p
pli/i-Widg
et
Setting the i-
α
ppli Standby
Screen
<Set i-
α
ppli stand-by>
You can set a selected i-
α
ppli software as the standby
screen.
z
Some software applications cannot be set as the
standby screen.
1 Software list screen (P.267)
o
(Set) “Stand-by display” “ON”
o
(Finish)
Activating the i-
α
ppli standby screen
You can activate the software set as the i-
α
ppli
standby screen.
1 On the i-
α
ppli standby screen
t
The i-
α
ppli is activated and “ ” or “ ”
flashes at the bottom of the screen.
Deactivating the i-
α
ppli standby
screen
<Release i-
α
ppli stand-by>
● Deactivating the i-
α
ppli standby screen
while running an i-
α
ppli
1 While running an i-
α
ppli
t
(1
second or longer) or
y
Select
any item:
Cancel …… Returns to the screen of running the
i-
α
ppli standby screen.
End …… Returns to the i-
α
ppli standby screen.
Terminate
……
Deactivates the setting of the
i-
α
ppli standby screen.
● Deactivating the active i-
α
ppli standby
screen
1
i
“SETTINGS/SERVICE”
“i-
α
ppli settings” “End stand-by
display”
2 “Terminate” “YES”
■ To cancel deactivating
“NO”
■
To end
“End”
The Standby i-
α
ppli reboots.
Checking the i-
α
ppli standby screen
exit information
If an error occurs that causes the i-
α
ppli standby
screen to be deactivated, you can check the recorded
information on the name of the software in which the
error occurred, the time of the error and the reason.
1
i
“i-
α
ppli” “i-
α
ppli action
info” “End stand-by info”
• Press
u
(FUNC), you can copy/delete
standby screen exit information.
N
<i-mode sites>
z
Some i-
α
ppli activate without displaying a
confirmation screen after an activation item is
selected.
(some i-
α
ppli cannot be stored in the FOMA
terminal.)
<Mails>
z
An i-
α
ppli activation specification cannot be
quoted even if you reply with a quote or forward an
i-mode mail.
<IC card function>
z
The software is not launched in the following
cases:
• When another function is running
• During calls
• The i-
α
ppli to launch cannot be found
N
z
Only a single i-
α
ppli can be set as the i-
α
ppli
standby screen.
z
If software that communicates is set as the
standby screen, it may not run correctly when
problems such as poor signal quality occur.
z
If you select “OFF” for “Stand-by net” in “Software
setting”, note that you may not be able to receive
timely information.
z
If “Dial lock” or “Original lock” for i-
α
ppli is set or
2in1 is set to B mode or Dual mode while the
i-
α
ppli standby screen is displayed, the i-
α
ppli
standby screen ends. If “Dial lock” or “Original
lock” is released or 2in1 is set to A mode, the
i-
α
ppli standby screen reappears.
z
When you switch tasks and display the standby
screen, the screen specified in “Stand-by display”
of “Display setting” appears even though the
i-
α
ppli standby screen is set.