manualshive.com logo in svg

Dentsply Sirona Sim Multi Bench, Operating Instructions Manual

Share
Download
Dentsply Sirona Sim Multi Bench Operating Instructions Manual Download Page 7

Dentsply Sirona
Operating Instructions Simulation Unit Sim Multi Bench

1 General Information

1.3 Notes on these operating instructions

66 82 384 D3684
D3684.201.01.02.02    07.2019

7

1.3

Notes on these operating instructions

1.3.1

General information about these operating instructions

Follow the operating instructions

Please familiarize yourself with the unit by reading through these
Operating Instructions before putting it into operation. It is essential that
you comply with the specified warning and safety information.

Keep documents safe

Always keep the operating instructions handy in case you or another
user require(s) information at a later point in time. Save the operating
instructions on the PC or print them out.

If you sell the unit, make sure that the operating instructions are
included with it either as a hard copy or on an electronic storage device
so that the new owner can familiarize himself with its functions and the
specified warning and safety information.

Online portal for technical documents

We have set up an online portal for the Technical Documents at http://
www.sirona.com/manuals. From here, you can download these
Operating Instructions along with other documents. Please complete the
online form if you would like a hard copy of a particular document. We
will then be happy to send you a printed copy free of charge.

Help

If you reach an impasse despite having thoroughly studied the operating
instructions, please contact your dealer.

1.3.2

Scope of these operating instructions

Device variants

These operating instructions are valid for the following simulation unit:

● Simulation workstation Sim Multi Bench

Equipment options

This document describes the full version of your unit. It may therefore
cover components that are not included in the unit you purchased.

1.3.3

Other valid documents

Other relevant documents

The simulation workstation can be equipped with additional components
that are described in separate sets of operating instructions. The
instructions as well as all warning and safety information they contain
must also be followed.

A separate set of operating instructions exists for each of the following
products:

● Treatment instruments

● Operating light LEDlight Plus

● Operating light LEDview Plus

● Monitor

● Phantom heads

Summary of Contents for Sim Multi Bench





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands