background image

Specification

Value

Installation altitude

Nominal current up to 1000 m above sea level.

Derating of output current (1% / 100 m) at 1000–3000 m.

Operation above 3000 m is not permitted.

EMC standard for emission and immunity

EN 61800-3

EMC immunity for functional safety

EN 61800-5-2 Annex E

Degree of pollution according to EN
60664-1

2

Overvoltage category according to EN
61800-5-1

III

O

u

tp

u

cu

rr

e

n

[%

]

100

90

80

70

60

30

35

40

45

50

55

e

3

0

b

h

1

0

6

.1

0

Illustration 155:  Derating

11.9 Storage

Store the servo system components in a dry, dust-free location with low vibration (v

eff

 

0.2 mm/s).

The storage location must be free from corrosive gases.

Avoid sudden temperature changes.

Long-term Storage

To recondition the electrolytic capacitors, servo drives and system components not in service must be connected to a supply source
once per year to allow the capacitors to charge and discharge. Otherwise the capacitors could suffer permanent damage.

Specifications

Operating Guide  | VLT® Multiaxis Servo Drive MSD 510 System

AQ262450196490en-000101 / 175R1170

238 | Danfoss A/S © 2019.10

Summary of Contents for VLT MSD 510























































































































































































































































Reviews: