Danfoss VLT MSD 510 Page 183 Operating Manual Download

Page: 183 / 246

Table 82: Configuration parameters limits error (0x6383 / 0x164)

Code

PROFINET

code

Name

Severity (warn‐

ing/error/trip

lock)

Description

LCP name

0x6383

0x164

Configuration pa-
rameters limits er-
ror

Trip lock

≥1 parameter in the configuration parameter
set is out of limits: the parameter set is not
valid for this device.

conf par
lim

9.3.48 Power EEprom configuration error (0x6384 / 0x166)

This error is valid for PSM 510, DAM 510, ACM 510, and SDM 511/SDM 512.

Table 83: Power EEprom configuration error (0x6384 / 0x166)

Code

Name

Severity (warning/

error/trip lock)

Description

LCP name

0x6384

0x166

Power Eeprom config-
uration error

Trip lock

The power device Eeprom is corrupt or
incompatible with this control board.

conf par EE-
PROM

9.3.49 Brake chopper failure (0x7111 / 0x141)

This error is valid for PSM 510.

Table 84: Brake chopper failure (0x7111 / 0x141)

Code

PROFINET

code

Name

Severity (warning/

error/trip lock)

Description

LCP name

0x7111

0x141

Brake chop-
per failure

Warning, error

The brake chopper is monitored during oper-
ation.

A brake failure has been detected by the
brake check function.

brake ch fail

9.3.50 Brake chopper overcurrent (0x7112 / 0x167)

This error is valid for PSM 510.

Table 85: Brake chopper overcurrent (0x7112 / 0x167)

Code

PROFINET

code

Name

Severity (warning/error/

trip lock)

Description

LCP name

0x7112

0x167

Brake chopper
overcurrent

Trip lock

The brake chopper current ex-
ceeds the limit.

brake ch over-
curr

9.3.51 Brake resistor maximum power limit (0x7181 / 0x142)

This error is valid for PSM 510.

Diagnostics

Operating Guide | VLT® Multiaxis Servo Drive MSD 510 System

AQ262450196490en-000101 / 175R1170| 183

Summary of Contents for VLT MSD 510























































































































































































































































Search results

Summary of Contents for VLT MSD 510

Reviews:

Related manuals for VLT MSD 510

Brands by name

Popular brands

Danfoss VLT MSD 510, Operating Manual

Search results

Summary of Contents for VLT MSD 510

Reviews:

Related manuals for VLT MSD 510

Brands by name

Popular brands