xStack
®
DGS-3400 Series Layer 2 Gigabit Managed Switch CLI Manual
174
23
MLD
S
NOOPING
C
OMMANDS
Multicast Listener Discovery (MLD) Snooping is an IPv6 function used similarly to IGMP snooping in IPv4. It is used to discover
ports on a VLAN that are requesting multicast data. Instead of flooding all ports on a selected VLAN with multicast traffic, MLD
snooping will only forward multicast data to ports that wish to receive this data through the use of queries and reports produced by
the requesting ports and the source of the multicast traffic.
MLD snooping is accomplished through the examination of the layer 3 part of an MLD control packet transferred between end
nodes and a MLD router. When the switch discovers that this route is requesting multicast traffic, it adds the port directly attached
to it into the correct IPv6 multicast table, and begins the process of forwarding multicast traffic to that port. This entry in the
multicast routing table records the port, the VLAN ID and the associated multicast IPv6 multicast group address and then
considers this port to be a active listening port. The active listening ports are the only ones to receive multicast group data.
MLD Control Messages
Three types of messages are transferred between devices using MLD snooping. These three messages are all defined by three
ICMPv6 packet headers, labeled 130, 131 and 132.
1.
Multicast Listener Query
– Similar to the IGMPv2 Host Membership Query for IPv4, and labeled as 130 in the
ICMPv6 packet header, this message is sent by the router to ask if any link is requesting multicast data. There are two
types of MLD query messages emitted by the router. The General Query is used to advertise all multicast addresses that
are ready to send multicast data to all listening ports, and the Multicast Specific query, which advertises a specific
multicast address that is also ready. These two types of messages are distinguished by a multicast destination address
located in the IPv6 header and a multicast address in the Multicast Listener Query Message.
2.
Multicast Listener Report
– Comparable to the Host Membership Report in IGMPv2, and labeled as 131 in the ICMP
packet header, this message is sent by the listening port to the Switch stating that it is interested in receiving multicast
data from a multicast address in response to the Multicast Listener Query message.
3.
Multicast Listener Done
– Akin to the Leave Group Message in IGMPv2, and labeled as 132 in the ICMPv6 packet
header, this message is sent by the multicast listening port stating that it is no longer interested in receiving multicast data
from a specific multicast group address, therefore stating that it is “done” with the multicast data from this address. Once
this message is received by the Switch, it will no longer forward multicast traffic from a specific multicast group address
to this listening port.
The MLD Snooping commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the
following table.
Command Parameters
enable mld_snooping
{forward_mcrouter_only}
disable mld_snooping
{forward_mcrouter_only}
config mld_snooping
[vlan <vlan_name 32> | all] {node_timeout <sec 1–16711450> |
router_timeout <sec 1–16711450> | done_timer <sec 1–
16711450> | state [enable | disable] | fast_done [enable |
disable]} (1)
config mld_snooping mrouter_ports
<vlan_name 32> [add | delete] <portlist>
config mld_snooping mrouter_ports_forbidden
<vlan_name 32> [add | delete] <portlist>
config mld_snooping querier
[ vlan <vlan_name 32> |all] { query_interval <sec 1-65535> |
max_response_time <sec 1-25> | robustness_variable <value 1-
255> | last_listener_query_interval <sec 1-25> | state
[enable|disable] | version <value 1-2>} (1)
show mld_snooping
{vlan <vlan_name 32>}
show mld_snooping group
{vlan <vlan_name 32>}
show mld_snooping mrouter_ports
{vlan <vlan_name 32>} {[static | dynamic | forbidden]}
Each command is listed, in detail, in the following sections.
