xStack
®
DGS-3400 Series Layer 2 Gigabit Managed Switch CLI Manual
200
D G S – 3 4 2 6 : 5 # s h o w a u t h _ c l i e n t
C o m m a n d : s h o w a u t h _ c l i e n t
r a d i u s A u t h C l i e n t = = >
r a d i u s A u t h C l i e n t I n v a l i d S e r v e r A d d r e s s e s 0
r a d i u s A u t h C l i e n t I d e n t i f i e r
r a d i u s A u t h S e r v e r E n t r y = = >
r a d i u s A u t h S e r v e r I n d e x : 1
r a d i u s A u t h S e r v e r A d d r e s s 0 . 0 . 0 . 0
r a d i u s A u t h C l i e n t S e r v e r P o r t N u m b e r 0
r a d i u s A u t h C l i e n t R o u n d T r i p T i m e 0
r a d i u s A u t h C l i e n t A c c e s s R e q u e s t s 0
r a d i u s A u t h C l i e n t A c c e s s R e t r a n s m i s s i o n s 0
r a d i u s A u t h C l i e n t A c c e s s A c c e p t s 0
r a d i u s A u t h C l i e n t A c c e s s R e j e c t s 0
r a d i u s A u t h C l i e n t A c c e s s C h a l l e n g e s 0
r a d i u s A u t h C l i e n t M a l f o r m e d A c c e s s R e s p o n s e s 0
r a d i u s A u t h C l i e n t B a d A u t h e n t i c a t o r s 0
r a d i u s A u t h C l i e n t P e n d i n g R e q u e s t s 0
r a d i u s A u t h C l i e n t T i m e o u t s 0
r a d i u s A u t h C l i e n t U n k n o w n T y p e s 0
r a d i u s A u t h C l i e n t P a c k e t s D r o p p e d 0
C T R L + C
E S C
q
Q u i t
S P A C E
n
N e x t P a g e
p
P r e v i o u s P a g e
r
R e f r e s h
show auth_diagnostics
Purpose
Used to display the current authentication diagnostics.
Syntax
show auth_diagnostics {ports [<portlist> | all]}
Description
This command is used to display the current authentication diagnostics of the Switch on a
per port basis.
Parameters
ports <portlist>
−
Specifies a range of ports. The port list is specified by listing the lowest
switch number and the beginning port number on that switch, separated by a colon. Then
the highest switch number, and the highest port number of the range (also separated by a
colon) are specified. The beginning and end of the port list range are separated by a
dash. For example, 1:3 specifies switch number 1, port 3. 2:4 specifies switch number 2,
port 4. 1:3–2:4 specifies all of the ports between switch 1, port 3 and switch 2, port 4 – in
numerical order. Non–contiguous portlist entries are separated by a comma. (ex: 1:1–
1:3,1:7–1:9)
all
– Specifies that all ports will be viewed.
Restrictions None.
Example usage:
To display the current authentication diagnostics for port 16 of module 1:
