D-Link Wireless N User Manual Download Page 12

Page: 12 / 153

D-Link DIR-815 User Manual

Section 1 - Product Overview

Power LED

A solid green light indicates a proper connection to the power supply. This LED will light orange during a factory reset or

reboot. A slow blinking orange LED indicates that the Router has crashed during bootup.

Internet LED

A solid green light indicates the PPP negotiation has successfully completed. This LED blinks green during data transmission.

A solid orange light indicates that the physical link is up, but the ISP service is down. This LED blinks orange when a session is

dropped due to idle timeout.

WLAN LED (2.4GHz)

A solid light indicates that the 2.4GHz wireless segment is ready. This LED blinks during wireless data transmission.

WLAN LED (5GHz)

A solid light indicates that the 5GHz wireless segment is ready. This LED blinks during wireless data transmission.

LAN LEDs (1-4)

A solid light indicates a connection to an Ethernet-enabled computer on ports 1-4. This LED blinks during data transmission.

Hardware Overview

LEDs

1 2

3 4

Summary of Contents for Wireless N


























































































































































Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands

D-Link Wireless N, User Manual

Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands