D-Link Wireless N User Manual Download Page 38

Page: 38 / 153

D-Link DIR-815 User Manual

Section 3 - Configuration

Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable

Auto-reconnect.

The DNS server information will be supplied by your ISP (Internet Service Provider).

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default

MTU.

The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended

that you change the default MAC address unless required by your ISP. You can use the

Clone.Your.PC’s.MAC.Address

button to

replace the Internet port’s MAC address with the MAC address of your Ethernet card.

Maximum Idle

Time:

DNS Servers:

MTU:

MAC Address:

Click the

Save.Settings

button to save any changes made.

Summary of Contents for Wireless N


























































































































































Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands

D-Link Wireless N, User Manual

Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands