D-Link Wireless N User Manual Download Page 120

Page: 120 / 153

115

D-Link DIR-815 User Manual

Section 5 - Connecting to a Wireless Network

Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility, please refer to the user

manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option

similar to the Windows Vista®

utility as seen below.

Right-click on the wireless computer icon in your system tray

(lower-right corner next to the time). Select

Connect.to.a.network

If you receive the

Wireless.Networks.Detected.

bubble, click on the

center of the bubble to access the utility.

The utility will display any available wireless networks in your area.

Click on a network (displayed using the SSID) and click the

Connect

button.

If you get a good signal but cannot access the Internet, check you

TCP/IP settings for your wireless adapter. Refer to the

Networking.

Basics.

section in this manual for more information.

Windows Vista®

Summary of Contents for Wireless N


























































































































































Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands

D-Link Wireless N, User Manual

Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands