D-Link Wireless N User Manual Download Page 62

Page: 62 / 153

D-Link DIR-815 User Manual

Section 3 - Configuration

Static.IPv6.Address.Connection

This mode is used when your ISP provides you with a set IPv6 addresses that does not change. The IPv6 information is manually entered in your

IPv6 configuration settings. You must enter the IPv6 address, Subnet Prefix Length, Default Gateway, Primary DNS Server, and Secondary DNS

Server. Your ISP provides you with all this information.

Use.Link-Local.

Address:

IPv6.Address:

Subnet.Prefix.

Length:

Default.Gateway:

Primary.IPv6.DNS.

Address:

Secondary.IPv6.

DNS.Address:

LAN.IPv6.Address:

The Link-local address is used by nodes and routers when

communicating with neighboring nodes on the same link.

This mode enables IPv6-capable devices to communicate

with each other on the LAN side.

Enter the WAN IPv6 address for the router here.

Enter the WAN subnet prefix length value used here.

Enter the WAN default gateway IPv6 address used here.

Enter the WAN primary DNS Server address used here.

Enter the WAN secondary DNS Server address used here.

These are the settings of the LAN (Local Area Network)

IPv6 interface for the router. The router’s LAN IPv6 Address

configuration is based on the IPv6 Address and Subnet

assigned by your ISP. (A subnet with prefix /64 is supported

in LAN.)

Summary of Contents for Wireless N


























































































































































Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands

D-Link Wireless N, User Manual

Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands