D-Link Wireless N User Manual Download Page 85

Page: 85 / 153

D-Link DIR-815 User Manual

Section 3 - Configuration

Routing

The Routing option is an advanced method of customizing specific routes of data through your network.

Click the

Save.Settings

button to save any changes made.

Enter the IP address of packets that will take this route.

Enter the netmask of the route, please note that the octets

must match your destination IP address.

Enter your next hop gateway to be taken if this route is

used.

The route metric is a value from 1 to 16 that indicates the

cost of using this route. A value 1 is the lowest cost and

15 is the highest cost.

Select the interface that the IP packet must use to transit

out of the router when this route is used.

Destination IP:

Netmask:

Gateway:

Metric:

Interface:

Summary of Contents for Wireless N


























































































































































Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands

D-Link Wireless N, User Manual

Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands