D-Link Wireless N User Manual Download Page 61

Page: 61 / 153

D-Link DIR-815 User Manual

Section 3 - Configuration

IPv6.over.PPPoE

After selecting the IPv6 over PPPoE option, the user will be able to configure the

IPv6 Internet connection that requires a username and password to get online.

Most DSL modems use this type of connection.

The following parameters will be available for configuration:

PPPoE.Session:

Select the PPPoE Session value used here. This

option will state that this connection shares it’s

information with the already configured IPv6

PPPoE connection, or the user can create a new

PPPoE connection here.

User.Name:

Enter the PPPoE username used here. If you do not

know your user name, please contact your ISP.

Password:

Enter the PPPoE password used here. If you do not

know your password, please contact your ISP.

Verify.Password:

Re-enter the PPPoE password used here.

Service.Name:

Enter the service name for this connection here.

This option is optional.

Summary of Contents for Wireless N


























































































































































Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands

D-Link Wireless N, User Manual

Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands