D-Link Wireless N User Manual Download Page 90

Page: 90 / 153

D-Link DIR-815 User Manual

Section 3 - Configuration

Guest Zone

Check to enable the Guest Zone feature.

The schedule of time when the Guest Zone will be

active. The schedule may be set to Always, which will

allow the particular service to always be enabled. You

can create your own times in the

Tools

Schedules

section.

Enter a wireless network name (SSID) that is different

from your main wireless network.

Check to allow network connectivity between the

different zones created.

Select the type of security or encryption you would

like to enable for the guest zone.

Enable Guest

Zone:

Schedule:

Wireless

Network Name:

Enable Routing

Between Zones:

Security Mode:

The Guest Zone feature will allow you to create temporary zones that can be used by guests to access the Internet. These zones

will be separate from your main wireless network. You may configure different zones for the 2.4GHz and 5GHz wireless bands.

Summary of Contents for Wireless N


























































































































































Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands

D-Link Wireless N, User Manual

Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands