D-Link Wireless N User Manual Download Page 15

Page: 15 / 153

D-Link DIR-815 User Manual

Section 2 - Installation

1. Turn off and unplug your cable or DSL broadband modem. This is required.

Manual Setup

POWER

RESET

INTERNET

12V 1A

Important:

for best results, insert the Installation CD and follow the on-screen instructions. If you are unable to use the CD or

are using Mac or Linux, please use the following installation steps:

2. Position your router close to your modem and a computer. Place the router in an open area of your intended

work area for better wireless coverage.

3. Unplug the Ethernet cable from your modem (or existing router if upgrading) that is connected to your computer.

Plug it into the blue port labeled 1 on the back of your router. The router is now connected to your computer.

Modem

DIR-815

Computer

Summary of Contents for Wireless N


























































































































































Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands

D-Link Wireless N, User Manual

Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands