D-Link Wireless N User Manual Download Page 16

Page: 16 / 153

D-Link DIR-815 User Manual

Section 2 - Installation

4. Plug one end of the included blue Ethernet cable that came with your router into the yellow port labeled

INTERNET on the back of the router. Plug the other end of this cable into the Ethernet port on your modem.

POWER

RESET

INTERNET

12V 1A

5. Reconnect the power adapter to your cable or DSL broadband modem and wait for two minutes.

6. Connect the supplied power adapter into the power port on the back of the router and then plug it into a power

outlet or surge protector. Press the power button and verify that the power LED is lit. Allow 1 minute for the

router to boot up.

POWER

RESET

INTERNET

12V 1A

7. If you are connecting to a Broadband service that uses a dynamic connection (not PPPoE), you may be online

already. Try opening a web browser and enter a web site. If you connect, you are finished with your Internet setup.

Please skip to page 14 to configure your router and use the manual setup procedure to configure your network

and wireless settings. If you did not connect to the Internet, use the D-Link Setup Wizard (refer to page 15).

DIR-815

Modem

Summary of Contents for Wireless N


























































































































































Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands

D-Link Wireless N, User Manual

Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands