D-Link Wireless N User Manual Download Page 34

Page: 34 / 153

D-Link DIR-815 User Manual

Section 3 - Configuration

The Host Name is optional but may be required by some

ISPs. Leave blank if you are not sure.

Enter the Primary and Secondary DNS server IP addresses

assigned by your ISP. These addresses are usually obtained

automatically from your ISP. Enter the value 0.0.0.0 if you

did not specifically receive these from your ISP.

Maximum Transmission Unit - you may need to change

the MTU for optimal performance with your specific ISP.

1500 is the default MTU.

The default MAC Address is set to the Internet port’s

physical interface MAC address on the Broadband Router.

It is not recommended that you change the default MAC

address unless required by your ISP. You can use the

Clone

Your PC’s MAC Address

button to replace the Internet

port’s MAC address with the MAC address of your Ethernet

card.

Dynamic IP (DHCP)

Select

Dynamic IP (DHCP)

from the drop-down menu to obtain IP Address information automatically from your ISP. Select

this option if your ISP does not give you any IP numbers to use. This option is commonly used for cable modem services such

as Comcast and Cox.

Host Name:

Primary/

Secondary DNS

Server:

MTU:

MAC Address:

Click the

Save.Settings

button to save any changes made.

Summary of Contents for Wireless N


























































































































































Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands

D-Link Wireless N, User Manual

Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands