D-Link Wireless N User Manual Download Page 18

Page: 18 / 153

D-Link DIR-815 User Manual

Section 2 - Installation

5. Under Router Settings, enter an available IP address and the subnet mask of your network. Click

Save.Settings

to save your

settings. Use this new IP address to access the configuration utility of the router in the future. Close the browser and change

your computer’s IP settings back to the original values as in Step 1.

6. Disconnect the Ethernet cable from the router and reconnect your computer to your network.

7. Connect an Ethernet cable in one of the

LAN

ports of the router and connect it to your other router. Do not plug anything

into the Internet (WAN) port of the D-Link router.

8. You may now use the other 3 LAN ports to connect other Ethernet devices and computers. To configure your wireless network,

open a web browser and enter the IP address you assigned to the router. Refer to the

Configuration

and

Wireless

Security

sections for more information on setting up your wireless network.

POWER

RESET

INTERNET

12V 1A

Summary of Contents for Wireless N


























































































































































Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands

D-Link Wireless N, User Manual

Search results

Summary of Contents for Wireless N

Reviews:

Related manuals for Wireless N

Brands by name

Popular brands