![background image](http://html.mh-extra.com/html/cisco/5505-asa-firewall-edition-bundle/5505-asa-firewall-edition-bundle_cli-configuration-manual_186241793.webp)
1-3
Cisco ASA Series CLI Configuration Guide
Chapter 1 Configuring the PPPoE Client
Enabling PPPoE
Enabling PPPoE
Note
You must complete the configuration using the
vpdn
command, described in “
,” before enabling PPPoE.
The PPPoE client functionality is turned off by default. To enable PPPoE, perform the following steps:
Step 1
Enable the PPPoE client by entering the following command from interface configuration mode:
hostname(config-if)#
ip address pppoe
[
setroute
]
The
setroute
option sets the default routes when the PPPoE client has not yet established a connection.
When using the
setroute
option, you cannot have a statically defined route in the configuration.
PPPoE is not supported in conjunction with DHCP because with PPPoE the IP address is assigned by
PPP. The
setroute
option causes a default route to be created if no default route exists. The default router
is the address of the access concentrator. The maximum transmission unit (MTU) size is automatically
set to 1492 bytes, which is the correct value to allow PPPoE transmission within an Ethernet frame.
Reenter this command to reset the DHCP lease and request a new lease.
Note
If PPPoE is enabled on two interfaces (such as a primary and backup interface), and you do not
configure dual ISP support (see the
“Monitoring a Static or Default Route” section on page 1-6
),
then the ASA can only send traffic through the first interface to acquire an IP address.
For example:
hostname(config)#
interface gigabitethernet 0/0
hostname(config-if)#
ip address pppoe
Step 2
Specify a VPDN group for the PPPoE client to use with the following command from interface
configuration mode (optional):
hostname(config-if)#
pppoe client vpdn group
grpname
grpname is the name of a
VPDN
group.
Note
If you have multiple VPDN groups configured, and you do not specify a group with the
pppoe client
vpdn group
command, the ASA may randomly choose a VPDN group. To avoid this, specify a VPDN
group.
Using PPPoE with a Fixed IP Address
You can also enable PPPoE by manually entering the IP address, using the ip address command from
interface configuration mode in the following format:
hostname(config-if)#
ip address
ipaddress
mask
pppoe
Summary of Contents for 5505 - ASA Firewall Edition Bundle
